This compact stud-mounted marker light gives you bright, reliable visibility and the flexibility to meet PC or P2 requirements depending on how you mount it, all while keeping fasteners hidden for a clean finish.
When you need more visibility without adding bulk, this TecNiq PC and P2 rated side marker light delivers. At just 1-3/4" long by 1" wide and 1/2" deep, it fits neatly on most surfaces while still putting out strong illumination from its two amber LEDs. It meets both PC and P2 specifications depending on mounting orientation, so even with its small size, it provides reliable brightness for clearance and marking needs. Running on 9 to 14 volts DC, its efficient and consistent without dimming or flicker.
Moisture, dirt, or vibration wont stop this light. The TecSeal urethane potting material seals the circuit board completely, protecting it from dust and water intrusion. Its built to be waterproof and submersible, so whether youre hauling through rain or washing down equipment, it stays dry inside and keeps working. The housing is also UV-resistant to prevent fading or cracking from sun exposure.
If youre after a clean, finished look, the stud mount design makes it easy. The stainless steel ground stud anchors the light securely while hiding any mounting hardware from view. No screws or exposed bolts-just a smooth fit that looks sharp and professional once installed. The included pigtail with a standard non-polarized connector keeps wiring simple too.
This light is made for the long haul. With solid-state LEDs and sealed electronics, there are no bulbs to replace or parts to rust out over time. TecNiq backs the PC and P2 rated side marker with a lifetime warranty, so once you install it, you can count on dependable performance mile after mile without worrying about replacements or failures.
California residents: click here
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Hello everybody, this is Jeff at etrailer. Today we're gonna take a look at the TecNiq S14 LED marker light and it's a stud mount design. Now this compact stud-mounted marker light's gonna give you bright, reliable visibility and even the flexibility to meet the PC or P2 requirements depending on how you're gonna mount this all while keeping the fasteners hidden for a nice clean finish. Now I am gonna hook this up to some 12-volt power just to show you how bright it is. You can see it's a single wire and then it'll ground with using the stud. So if I get my wires here, we go ahead and hook our power wire up.
Whoops. Let's get that again. Hook up our power wire. And with that hooked up, we'll go ahead and turn on our power and then we'll ground it again by touching the stud back here. You'll see just by touching that, that's your ground.
So you'll see when we touch it, there's the light. What we'll go ahead and do is turn off the overhead lights. Now you can see when I ground it, it gives you a nice bright two LEDs in there, bright light. Go ahead and turn back on our overhead light. Disconnect it.
Now it's one and three quarter inches long, one-inch wide, about a half inch deep, so it's gonna fit neatly on most surfaces while still putting out a strong illumination from those two amber LEDs. It does provide reliable brightness for clearance of marking needs. And again, it'll run on nine to 14 volts DC. It's very efficient and consistent without dimming or flickering. It does use a TecSeal urethane potting material, which will seal the circuit board completely, protects it from any dust and water intrusion.
It is built to be waterproof and submersible, so whether you're hauling through rain or washing down equipment, it'll stay dry inside and keep working. The housing itself is UV-resistant, prevents fading or cracking from sun exposure. So what's nice is if you have, if you're after a nice clean finish look, the stud mount design we mentioned makes it very easy. The stainless steel ground's gonna stud and it anchors the light securely while hiding any mounting hardware from view. No screws or exposed bolts, just a nice smooth fit. Looks sharp and professional once it's installed. We mentioned a pigtail wire and it uses a standard non-polarized connector. Keeps the wiring simple too. And these are LEDs, so there's no bulbs to replace or parts that will rust out over time. Now if you do have any other additional questions regarding this part or any other item we carry, please feel free to reach out to us so we can help you get all of your questions answered for you. But that's gonna do it for our look at this TecNiq S14 LED marker light in a stud mount design.
Easy to install, works great
Info for this part was:
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.