See what our Experts say about this Erickson E Track

• Mounting Suggestion For E-track To Aluminum Utility Trailer
  For your Aluma 6810 HBT trailer, I recommend the Erickson Horizontal E-Track - Zinc Coated Steel - 2,000 lbs - 5' Long - Qty 1 # E19148 along with the E-Track Backing Plate - Zinc Plated Steel - 6" Long x 6" Wide # e96RR. This will save you the expense of the dual track and will allow you the flexibility of plates between the braces or around them. This track also comes in 4 foot # EM19147, and 2 foot # EM59150. I recommend using the E-Track Plastic End Cap # ET8730 to finish your tracks. For...
  view full answer...
  
• Option to Carry Kayaks with E-Tracks Inside Cargo Trailer
  I am not aware of an e or x-track accessory that is designed specifically for carrying kayaks but we do have options for this assuming the tracks are on the walls. I recommend using a few CargoSmart Large Rotating Flat Hooks part # 3481701 to suspend the kayaks and then a few Erickson E-Track Straps with Ratchet part # EM59136 to hold them in place. The Erickson E-Track Tie Down Ring part # 59131 along with some standard ratchet straps can be used as well.
  view full answer...
• B and W Biker Bar for Harley Street Glide and Ultra Models
  Hey Donnie, for all three of your Harleys the correct Biker Bar would be the part # BWMC2301. BUT we don't have a solution for the Indian. They only have options for Harleys at this time. I wish they would make options for other brands as this does come up. So to transport it you'd need something like E-Track # e95VR, Wheel Chock # 3481731, Tie-Down Ring # 59131, and Strap # EM59136. Think that would work for you?
  view full answer...
• Will Biker Bar Fit 2011 Harley Superglide Custom
  Hi Eric; B&W doesn't have specific fitment information for a 2011 Harley Superglide Custom. However, you may be able to use the B&W Biker Bar # BWMC2304. To find out if it will fit you will have to take some measurements. A two piece motorcycle tube frame is needed for the Biker Bar to clamp onto. The diameter of each frame tube must be at least 1.125" and no more than 1.5". Check that there is nothing hanging down below the tube frame, such as a motor, transmission or exhaust. With the...
  view full answer...
• Will Biker Bar Fit 2022 Indian Chieftain Limited
  Hey Paul; B&W hasn't tested the 2022 Indian Chieftain Limited but it may fit the # BWMC2304. To find out if it will fit you will have to take some measurements. A two piece motorcycle tube frame is needed for the Biker Bar to clamp onto. The diameter of each frame tube must be at least 1.125" and no more than 1.5". Check that there is nothing hanging down below the tube frame, such as a motor, transmission or exhaust. With the rider sitting on the motorcycle, the distance from the side...
  view full answer...
  
• Is There Biker Bar For Indian Super Chief Limited
  Hi Kristi, B&W does not make a Biker Bar for your Indian Super Chief Limited, so to transport it you'd need something like E-Track # e95VR, Wheel Chock # 3481731, Tie-Down Ring # 59131, and Strap #EM59136.
  view full answer...
• What Motorcycle Frame Tube and Frame Width Do the B&W Biker Bar Motorcycle Tie-Down System Fit
  The B&W Biker Bar Motorcycle Tie-Down Systems we carry are only designed to fit certain models of Harley-Davidson and have not been tested for other bikes like your Kawasaki Vulcans. It is possible they can work with your bikes if they have double tubes but you will need to know a couple of dimensions, the frame tube diameters and the frame width. The B&W Biker Bar Motorcycle Tie-Down System for Trailers - Harley-Davidson Touring # BWMC2301 requires a frame tube diameter of 1-1/8" to...
  view full answer...
  
• Can Buyers Products Sliding Winch Track Be Used as Trailer Tie Down Anchor
  Yes, the Buyers Products Sliding Winch Track # 3371903040 can be installed on a flat steel surface to secure a load, as you mentioned. Since it's designed to allow a winch to slide along that channel, for this purpose, the channel must face down. However, installing it with the C-channel facing up does not affect its functionality for your application. That being said, I believe the Erickson Horizontal E-Track - Zinc Plated Steel - 2,000 lbs - 5' Long # E19148 will work much better for...
  view full answer...
  
• E Track Placement Recommendation for Motorcycle Trailer
  Basically you'll have to mock up where you want the motorcycle to be and where the best place will be for the e-track as there isn't a set place to install the tracks in every trailer. Typically you want the tie down anchors to be about 36 inches apart from each other to get the best angle for them to pull down. For tie down anchors that fit in the e-track slots we have the part # 59131 which would fit and work well. Then for a set of ratchet straps the Erickson kit part # EM31353 would...
  view full answer...
• Single E-Track Anchor for E-Track Tie-Off Ring # 59131
  In the picture, the customer is using the Erickson tie-off ring # 59131 with single E-track anchor, # SLSB. There is also a stainless model, # SLSS, and a zinc model, # SLSZ. If you want one you can paint yourself there is also an unfinished model, # SLSU. I have linked a couple of videos to the right for you. There are all kinds of E-track accessories that could be used in the anchors. I have also included a link with the accessories, anchors, and tracks for you.
  view full answer...
  
• E-Track Recommendation for Securing ATV to Utility Trailer
  E-track can easily attach to the wood floor you have in your open utility trailer. This is a very common style of trailer that is used with the E-tracks. I attached a couple review videos that show etracks installed in a similar trailer as yours and what they use to secure the cargo. The etrack sections like the part # E19148 would be more than adequate to secure your ATV. The # 59131 is a great anchor to use, or if you want a strap that attaches directly to the etrack we have the # EM59136...
  view full answer...
  
• Where to Install E-Tracks in Enclosed Trailer Carrying Polaris ATV and Motorcycles
  Since you will be using your E-Track system, part # E19148, for transporting more than one type of vehicle, you will want to try to find mounting locations that will work for all of them. The main consideration for deciding where to mount the E-Tracks is to select locations that provide access to structural components, such as wall studs and floor supports. These structural elements of your trailer will serve as the backbone of your E-Track system. It is important that the tracks mount...
  view full answer...
• E-Track and Parts Needed For Securing Motorcycles In a Enclosed Trailer
  Yes, you can place the etrailer Horizontal E-Track # e25VR across your trailer from side to side. This will allow you to use the CargoSmart Motorcycle Wheel Chock # 3481731 making it easier and safer to secure your bikes in your trailer. Be sure to use the etrailer E-Track Backing Plates w/ Hardware # e46RR to secure each of the 5' tracks in place. Each of these kits includes 3 brackets for each track. I recommend using the Erickson E-Track Tie Down Rings # 59131 and Cam Tie-Downs # EM05729...
  view full answer...
• E-Track Recommendations For 7 By 14 Enclosed Trailer To Carry Classic Motorcycles
  With cargo like your two classic Harleys you will want to make sure they are really well secured to prevent any damage. I recommend securing the E-Tracks to something more stable than just wood. If you are attaching the tracks to the floor I recommend you make sure they are secured either to the metal structure of the trailer or use metal plates like the E-Track Backing Plate, part # e96RR, to make it as secure as possible. If the interior floor and walls are 7 ft long I recommend 5...
  view full answer...
  
• How Does Etrailer Slot and Anchor Typically Install on Truck Tailgate
  Sounds like you are talking about using a single E-Track slot like part # SLSB to instal the Erickson E-Track Tie Down Ring # 59131 in a tailgate application like the picture we recieved from a customer who did the same. There isn't an exact recommended way to accompolish this. It looks like the picture you referenced has a tailgate that has an internal panel that can be removed so that the customer could use nuts and bolts to hold the slot to the side of the tailgate. We don't have exactly...
  view full answer...
  
• E-Track Recommendation to Secure 4 Motorcycles in an Enclosed Trailer
  You would be more than okay to run two tie downs off of one the E-Track Tie-Off Ring part # 59131 that you referenced. Each of these has a 4,000 lb capacity which would be more than enough for what you are doing. Your plan to use 9 of the E-Tracks # EM59150 with the # 59131 like the drawing you sent in would work perfectly. For backing plates you could use the part # e96RR. I attached an install video for the E-track for you to check out as well.
  view full answer...
  
• Can the Erickson Horizontal E-Tracks Be Mounted On a Ceiling for Punching Bag
  E-track can be used on a ceiling since it is designed to hold quite a bit of weight to the track. Commonly people secure vehicles to the track on the floor of a trailer so a ceiling mount (through a stud) to hold a punching bag would be definitely doable. For an anchor with a ring to use with the track # E19148 you'd want just the part # 59131.
  view full answer...
• Anchoring E-Track On Floor Of Van For Transporting a Motorcycle
  To secure the Erickson Horizontal E-Track # EM59150 you need to use the E-Track Backing Plates # e66RR to secure them to the floor. The screws can easily pull out of the plywood especially considering your van will be absorbing a lot of road shock. You will want to ensure that the plywood is also secured to the floor either with the backing plates or in another similar manner. This will ensure that your Harley stays secured to the floor and will not move. I recommend using the Erickson...
  view full answer...
• Hardware Recommendation for Securing E Tracks to Plywood Trailer Floor
  Securing the Erickson E-Track # E19148 to 3/4 inch plywood should be sufficient. To secure the track to the plywood, you can use screws, or rivets. Using 1/2 inch screws would be a good length with 3/4 inch plywood. You will want to attach screws at least every other mounting hole. For tie downs and straps I would recommend either the E-Track Tie-Off Ring # 59131, or E-Track 2 inch D-Ring, part # E59143. Also available is the Erickson E-Track Strap with Ratchet, part # EM59136.
  view full answer...
• Can the Erikson E-Track System Be Used In An Aluminum Utility Trailer
  The Erickson E-Track system will work great in your aluminum utility trailer, but you will want to put a layer between the E-Track and the aluminum of your trailer. This layer will help prevent corrosion cause by contact of dissimilar metals. This layer can consist of almost any material, such as wood, rubber, or plastic. When installing the E-Track system in a trailer, one thing to keep in mind is to select locations that provide structural components, such as wall studs and floor supports....
  view full answer...
• Is it Possible for E-Track and Snowmobile Carbides to Scratch Each Other
  From what I understand about snowmobiles, and please correct me if I am wrong because I have little knowledge on them, the carbides are the part the skis attach to. Is that correct? I am not sure how the E-track or the carbides would come into contact with each other. But if they did then it would be possible for one to scratch the other. To avoid that you could use 3 lengths of tracks; one on the far left side and one on the far right with one in the center between the snowmobiles so...
  view full answer...
• E-Track and Motorcycle Wheel Chock Recommendation for Securing Motorcycle to Trailer
  That sounds like a great plan, the E-Track part # E19148 will provide a great tie-down point for securing the motorcycles. For tie-down rings you would want the # 59131 and then for a wheel chock I would recommend the # 3481731 because of how well it secures motorcycle and how easy it is to use. Check out the review video I attached for more info.
  view full answer...
• Will E-Track Tie Down Anchors Fit in Snap Lock Horizontal and Vertical E-Track
  Yes, the Erickson E-Track Tie Down Ring item # 59131 you referenced can be installed in the Snap-Lock Horizontal and Vertical E-Track item # SL27FR. Those Tie Down Rings can handle quite a bit of weight but it is going to come down to the anchors you are using to attach the vertical E-track to determine how much capacity they can handle.
  view full answer...
• E-Track Recommendation for Installing on the Inside of a Carson Fun Runner Toy Hauler
  Sounds like a good plan. For the 5 foot sections of the E-track you would want part # E19148. The # EM59150 that you referenced is sold in 2 foot sections. You might also be interested in the E-Track Tie-Off Ring # 59131, E-Track Wood Beam Socket # 59149, and E-Track 2" D-Ring part # E59143.
  view full answer...

Do you have a question about this E Track?