Best Toyota Prius Camper Jacks

We replaced our 3500 lb jack with this one because we wanted something faster and stronger and this jack is all of that. However, the number 1 reason we bought this jack is that it is easy to mount the head 90 degrees so that you can easily drop your tailgate down while hitched to our camper. It was easy to mount and it works like a charm.

We use this on a portable egg mobile in Maui, HI with very rough agricultural terrain. It gets moved 2 times a week and it is working like a charm! Saves lots of time in the field. Mahalo Nui Loa - Thanks very much, for a great product. Attached is a construction photo of the egg mobile.

I drilled two 3/8" holes in the top of the rail and used two stainless bolts to hold it on. Works very well for this application. It folds and holds the trailer for loading, and if I have to leave it somewhere, and don't want the tongue sitting on the ground. I used it on a Harbor Freight 4x4 trailer I am building to pull with my Can-Am Spyder. Love it!!!

I purchased this jack for my 2010 Escapade Elite trailer. I finally installed it yesterday. After a quick and minor modification, it fits great and funcltions like a charm. I highly recommend this product to other MC trailer owners. Thanks, etrailer.com for the quality and price!

if I had to rate this upgrade in difficulty one being the easiest five being the hardest, it would be a one. Super simple. Take the nuts and bolts off your old hardware and install the upgrade in its place. I read some of the reviews were people were annoyed with the counter clockwise rotation and the bolt sticking out too far. I really didn’t see a problem with either. I know you’re not supposed to use a drill to extend and retract these but I always have. I suppose as long as you’re not torquing the heck out of the adjustment screw you shouldn’t have any problems. I always put a small flat 2 x 6 piece of wood under the foot of each one of these. It seems to add quite a bit of stability.

The jacks themselves have worked great, they keep the trailer level and solid during our concession events. I just had them mounted to the trailer so I don't have to put them in and out at each event. The jack handles leave a bit to be desired so I use a 20v drill w/ a 3/4" socket to run them up and down.

Overall the product does exactly what it's intended for and works well. I however assumed that this would be a simple R&R for my camper and did very little installation research other that the video provided on etrailer' s website Sadly it did not fit. Not at all. I didn't take into account that have a double framed hitch toyhauler. The baseplate on the factory leg was a TRIANGLE.....this unit was ROUND. Also the primary shaft was thicker than stock and would not drop down into place I know modifying is frowned upon, but I found that ALL powered hitch legs I found have round mounting plates and it's not mentioned the leg tube is thicker than OEM? Since NOT having a power lift wasn't an option for this camper application...too heavy in the front when ATVS loaded to lift for setting the equalizer hitch tension bars, I proceeded to modify by cutting the rear rounded mounting base ... square. Took off about 1/2 inch. Then I took my metal Dremel sanding bit and increased the hitch leg hole diameter slightly. Took about 1 hr. Dropped it in. Wired it. Tested it. All good. If you can't post this I understand, but take note that some of your website descriptions may need to be enhanced. Thanks!

I ordered the Reese Bulldog 4000lb power tongue jack on 6/2 and received it on 6/6, my second order from etrailer and it came just as fast as the hitch that I ordered from them previously. The jack was characteristically well packaged so everything was received in perfect condition. The installation took a half hour, including hitching the trailer up to my truck and unhitching after the swap out. I did read the instructions quickly before starting and I would recommend that anyone doing the installation do so as well, just to avoid any hick-ups. Overall it was a very easy installation. Because of limited space I did have to mount the jack sideways, so I appreciate that Reese gave me that option. The one item that I did not finish was a permanent power hook-up. The power wire provided was too short so I will be putting a connector inline so that I can route the wire to the battery terminal.

Works great for a small camper. Easy to adjust and deploy. The stacking and storing is nice. I chose this option because we tow off road a lot and the less attached to the bottom of the camper the better!

These Jack's made both building and positioning my teardrop onto the trailer bed easier. At campsites they easily level the trailer. So yes I'm happy.

This was installed on my 3 point back blade and should work well for storage. It looks to be well enough made and hopefully provides many years of service. My Land Pride blade had holes in frame for a stand so I used those for mounting. By welding stand housing to a flat plate with matching holes it was simple to install. I did however mount it fairly high allowing back blade to turn fully around for reverse usage of blade. This will eliminate my routine of dropping it for storage and looking for a 5 gallon bucket to keep it at height.

Added a pair to the rear of my 10x5 landscape trailer and they work great. Units were installed by a professional welder and I did the touch-up black paint. Plan to add two more units to front corners for wheels off storage.

One of the best additions to our 5th wheel yet! I added these myself and it was not too hard, but I do have the proper tools. One install issue was around the pushout where I had to modify a bracket(see photos) We did a coast to coast and stayed in a LOT of places. These jacks worked very well as long as I got reasonably level side to side first. A few inches out is fine so most spots were a breeze, a few I needed to be on blocks so the tires did not come off the ground. The phone app is great to see initial level from the drivers seat, but I did most final leveling from the control pad. Overall great product and I recommend them especially if you are setting and breaking camp a lot.

shipped in a timely manner. Easy install wit good instructions. I did have one question about the location of the rear lifts and called the company and we had an answer instantly. Wiring was very easy with good instructions. The system worked on the first try and have had no issues so far. Great system. I was looking at newer campers with auto leveling and about 40 to $50,ooo if I traded my paid for camper in. The cost saved me a lot of money and works as it should and saves my back and a lot of set up time. would and have recommended to others. Thanks.

I should have got one years ago. I only use it when it's connected to the truck with the engine running. This I believe gives me full power. It has enough power to raise the trailer when connected to the truck to get the anti sway bars attached. Sure beats all that hand cranking.

The alternate power setup makes its slow rate of rise necessary which would be good if my lithium batteries went low. To avoid battery problems be sure to add an inline battery disconnect from the trailer power when using tow vehicle power. I simple added an inline fuse that could be removed should I need to use the tow vehicle power.

After the initial installation there was a little confusion about setup I have been very happy with the way it works really simple push one button hit auto levels it's still working well thanks

Let me say this to start, this system is AWESOME!! If you do not have a leveling system on your camper, this one works very , very well. I will say, the install and the learning curve takes time and is not too hard, but it's not super easy either. Once I got the system in place, and understood how to use it, the rest was a piece of cake. Take your time on the install and get help. The parts are robust and heavy, so two people make it much easier. Have sharp drill bits to drill the attachment holes. Wiring is super simple, but take your time and make sure you get all the connections good and tight and secured well with zip ties. The system requires a good strong battery, so make sure your battery is in great shape and you will not have any issues. Get the Lippert app also, it is very helpful. I love it now, when I pull my 2006 Keystone Raptor 5th wheel toy hauler into a campsite, I hit a couple buttons and the longest it has taken to level my unit is 2 minutes and 30 seconds. I love it! It puts the camper at the same level every single time, which is awesome. No guessing, no driving up and down on blocks, just push a button and walk away until the camper is perfect. Would I do this over again you ask? Absolutely. Awesome system!

I mounted this Stabilizers Jacks to the back of a 4x8 utility trailer. I use the trailer to haul my Honda ATV to MotoAmerica motorcycle races. Once the ATV is removed I lower the jacks and mount my tent inside the trailer. These stabilizers allow me to safely move around in the tent without fear of the trailer tipping.

Does not ratchet up, a pin must be manually inserted. It only came with one 6" long pin, which needs to be cut in half to make these stands functional. This is more like a folding jack stand, but the pin is not connected to the stand with a lanyard. I will be cutting the bar in half and welding a washer to hold it in place. I will also need to add a lanyard to it so I don't loose it. I would not recommend this product, but I have not found a better substitute for my application.

I really enjoyed working with Lauren she really knows the product line and the Ultra fab landing gear work far better than I expected. I have a 2019 Genis Supreme 33CKXL I highly recommend this product.

I recommend this landing gear set to everyone!!!!! After 2 replacements of tandem landing gear sets performed by dealership under warranty and still struggling lifting my 5th wheel, I decided to purchase this upgrade on my own dime. Best money I’ve spent in years. These lift my 15,000-16,000 5th wheel with no issues. Consistent and quiet. I don’t stress out anytime I’m hitching or unhitching anymore. 100% recommend buying. I’ve already talked 2 of my friends to do this upgrade and they love it.

These jacks are very well built and are strong enough for the job. I can't say how they will work for a large camper. I removed a shell, which required some creativity because the tripods are in front of the wheels, and impossible to drive the truck out from underneath. See pictures, they are worth a million words.

My husband is thrilled with the truck camper jacks. And the price is great too. Thank you.

These camper jacks arrived with a damaged protective weather seal. When I contacted etrailer for a replacement, they told me there were no replacement parts available and nothing they could due about it. The failure appeared to be a result of poor packaging. Very disappointing for an expensive item.

Works great as a stabilizer. I have a 38' trailer and I use screw jacks to level the trailer. Once the trailer is level I lower the stabilizer jacks to eliminate any movement. With this combination the trailer does not move one bit.

There's not a lot to say. The first Stabilizer carton was damaged to the point the carrier couldn't even find the Stabilizer. etrailer.com was very cooperative & sent a second unit out right away. Although the second shipment packaging was damaged all parts were there and undamaged. I installed the unit and it is so so much better, quieter and faster than the old unit. I highly recommend both Lippert and etrailer.com

The product is easy to install. It should be redesigned to allow more space between the trailer and the ground pad when in the travel position. There is interference between the pad and trailer that does not allow full locking in the travel slot. See pictures. A spacer for mounting would improve this feature.

I'm using the jacks to level the tailgate on my trailer so it can be used as a deck. They are easy to adjust for terrain variations