Best Toyota Camry Roof Racks

Mount: Custom DK Fit Kit for 4 Rhino-Rack 2500 Series Roof Rack Legs on a 2017 Toyota Camry

Today on our 2017 Toyota Camry, we'll be taking a look at the Rhino-Rack Vortex Aero roof rack. Part number for our crossbars today is RRVA118B-2. For our Rhino-Rack 2500 series legs, we're using RRRLKVA. For our custom fit kit for our Camry, we're using DK321. The Rhino-Rack Vortex Aero crossbars are an aerodynamic aluminum crossbar that will be perfect for your vehicle's roof. It's going to allow you to carry many roof rack accessories on your vehicle's rooftop. The roof rack system allows for channel mount accessories.

DIY 2017 Toyota Camry Installation for the Inno Aero Flush Roof Rack for Naked Roofs

Today on our 2017 Toyota Camry, we'll be taking a look at the Inno Aero Roof Rack System. Part number for our cross bar is INXB108-2, for our Inno Flush Feet we're using INXS200, and for our custom fit for our Camry we're using INK872. The Inno Aero Cross Bars are low profile, aerodynamic cross bars that allow you to carry any roof rack accessory on your vehicles roof. The cross bars help to reduce wind noise and drag giving you a smooth and quiet ride. The weather strip on the inside allows for use of channel mounted accessories. You would just push the weather strip down to insert that in which is also going to help reduce that wind noise and drag when you have those accessories on top. These cross bars also accommodate the clamp-on style accessories as well. The Inno Cross Bars allow you to open up space inside your vehicle by carrying all of your accessories on your vehicle's roof.

Install: Yakima RidgeLine Roof Rack for Flush Rails on a 2016 Toyota Camry

Speaker 1: Today on our 2016 Toyota Camry we're going to be test fitting the Yakima Core Bar Roof Rack System. The Yakima Core Bar Roof Rack System is great for carrying a wide variety of accessories on your Camry, such as bike racks, cargo baskets, and cargo boxes. It combines two things. It combines the strength of the round or square bars with the aerodynamics of your aero bars. While it is aerodynamic, it is going to cut down wind noise or drag. However, you cannot use T-track accessories with these bars.

Thule Traverse Roof Rack Installation - 2016 Toyota Camry

Today on our 2016 Toyota Camry we're going to be test fitting the Thule square load bar roof rack system consisting of part numbers THLB50, those are the Thule square load bars 50" long, part number TH480 this is the Thule traverse roof rack foot pack, and part number THKIT1438, this is the Thule fit kit for the Camry. The Thule square bar roof rack system is great for carrying a wide variety of accessories and freeing up space inside your vehicle. It is a clam on style, very easy to install and comes with its own tightening tool which can go with you to each location. If you choose, you do have the option of adding Thule lock cores to the end caps here, so once it's installed you can actually secure it to your roof. These are sold separately and you can find them on etrailer.com. The square bars are very nice and sturdy bars to put on your roof, and with the pair they have a carrying capacity of 165 pounds, although you always want to double check with your vehicle's manual to ensure your roof can withstand that weight. Now that we've gone over some of the features of the roof rack, let' go ahead and show you how it installs. We already have our front bar installed.

DIY Install: Custom DK Fit Kit for 4 Rhino-Rack 2500 Series Roof Rack Legs on your 2016 Toyota Camry

Today on our 2016 Toyota Camry, we're going to be test fitting the Rhino-Rack 2500 Roof Rack System, part number DS118B, these are the square crossbars 46" long, and part number DK321, and this is the custom fit kit for the Toyota Camry. The Rhino-Rack square bar roof rack is great for carrying a wide variety of accessories on your roof while freeing up space in your vehicle. It can carry anything from a bike rack to a cargo basket to an enclosed cargo box to ski and snowboard carriers and water sport carriers such as kayaks or canoes. The square bars are light-weight and durable and have a combined carrying capacity of 165 pounds, although you always want to double-check with your vehicle's manual to make sure it can withstand that weight. All four of our legs have these locking end caps, so once you install this onto your roof, it will be secured to your roof as well. Now that we've gone over some of the features of the roof rack, let's go ahead and show you how this goes on. We already have the front one installed, and we have the rear one in place here, which is partially assembled already. We'll start by flipping the bar upside-down and installing our leg. Here's our leg.

Set up: Inno Square Bar Roof Rack for Naked Roofs on a 2016 Toyota Camry

Today on this 2016 Toyota Camry, we're going to be test fitting the Inno Square Bar Roof Rack System consisting of part numbers INB127, these are the Inno Square Crossbars 50 inches long; part number INSU-K5, these are the Inno feet for the square crossbars; and part number INK872. This is the custom fit kit for the Camry. The Inno Square Bar Roof Rack System is great for creating a wide variety of accessories on your roof while freeing up space in your vehicle. Our self-tensioning knobs here at the end will lock into place. Once this is attached to your roof, it's secured to your roof as well. The square bars are nice and sturdy and have a carrying capacity of 120 pounds, although you always want to double check with your vehicle's manual to make sure it can withstand that weight. Now that we've gone over some of the features of the roof rack, let's go ahead and show you how it installs.

Rhino-Rack RS 2500 Vortex Aero Roof Rack Installation - 2016 Toyota Camry

Today on our 2016 Toyota Camry, we're going to be test fitting the Rhino Rack RS2500 Roof Rack System, part number RRRS346B. This also comes in silvers, part number RRRS346. The Rhino Rack RS2500 Series Roof Rack System, is great for carrying a wide variety of accessories on your roof, and freeing up space in your vehicle. It can carry bike racks, cargo baskets, cargo boxes, water sport carriers, ski and snowboard carriers. All of our legs come with these locking end caps, so once you install this to your roof, it's actually going to be secured to your roof as well. With the two bars combined, it has a carry capacity 165 pounds. You always want to double check with your vehicle's manual to make sure it can withstand that weight though. Let's go ahead and show you how this installs.

How to Install: Inno Aero Roof Rack for Naked Roofs on your 2016 Toyota Camry

Today, on our 2016 Toyota Camry, we're going to be test fitting the Inno Aero roof rack system consisting of part numbers INXB130-2, these are the Inno Aero crossbars, 51-inches long, part number INXS250, and these are the Inno through feet for the Aero crossbars, and part number INK872, and this is the custom fit kit for the Toyota Camry. The Inno Aero roof rack system is great for putting accessories up on your roof and freeing up space inside your vehicle. With removing our end cap here, you can see it has this nice rubber strap along the center here. Now, that coupled with the aerodynamic features of the bar will cut down wind noise and drag. Also, by pushing down on this, you can install T track accessories for your roof rack. Now, a lot of other roof racks will require you to remove the rubber strip and cut it to length, but this, all you have to do is push it down. Then reinstall your end cap. All of our through feet have these locking end caps here, so once you install this onto your roof, it's going to be secure to your roof.

Setting up the Custom DK Fit Kit for 4 Rhino-Rack 2500 Series Roof Rack Legs on a 2016 Toyota Camry

Today in our 2016 Toyota Camry, we're going to be taking a look at the Rhino Rack Vortex Aero roof rack system consisting of part number RRVA118B-2. These are the Vortex Aero cross bars 46" long. We'll also be using part number RRRLKVA. These are the 2500 series legs for the Vortex Aero cross bars. And part number DK321. This is the custom fit kit for the Toyota Camry.

Installation Guide for the Inno Aero Flush Roof Rack for Naked Roofs on a 2016 Toyota Camry

Today, on our 2016 Toyota Camry, we're going to be test fitting the Inno Aero crossbar roof rack system consisting of part numbers INXB108-2, these are the Inno Aero crossbars, 42-inches long, part number INXS200, these are the Inno flush feet for the Aero crossbars, and part number INK872, and this is the custom fit kit for the 2016 Toyota Camry. The Inno Aero roof rack system is great for carrying accessories up on your roof and freeing up space in your vehicle. Our bars have a rubber strip in the center and if you push this down, it'll enable you to use T track accessories for your roof rack. The rubber strip combined with the aerodynamic shape of the bars will also cut down wind noise and drag while you're driving. Now, when you push down to install your T track accessories, this is a bit of an advantage against other racks where you usually have to either cut or remove them to install these. These have locking end caps, so once you install this onto your roof, it will be secure to your roof, as well. Both bars have a combined carrying capacity of 165-pounds, although, always double check with your vehicle's manual to make sure it can withstand that weight. Now that we've gone over some of the features of the roof rack system, let's go ahead and show you how it installs.

Does the Rhino-Rack Vortex Aero Crossbars Suit Your 2014 Toyota Camry

Today on our 2014 Toyota Camry, we're going to be test-fitting the Rhino Rack Vortex Aero Roof Rack System in silver. We'll begin our test-fit by assembling one of the fit kits. We've got our Aero Blade here, part number RRVA118S-2. We have our Foot Pack, part number RRLKVA, and our Fit Kit, part number DK321. We'll go ahead and assemble this for you. That way you've got an idea how to do it at home.

Fit Check: Testing Rhino-Rack Vortex Aero Crossbars on a 2014 Toyota Camry

Today on our 2014 Toyota Camry we're going to be test fitting the Rhino-Rack Vortex Aero Roof Rack System in black part numbers RRVA118B-2 for our Aero Bar RRRLKVA for our foot pack and DK321 for our fit kit. We went ahead and assembled an installed the rest of the foot packs but I'll go ahead and show you how to do it on this one. The arrow here on the bottom of the bracket is going to face toward the outside of your vehicle. You also have an arrow on your pad here and that's going to be facing the front of the vehicle. We'll go ahead and press this on and move our bolt here, lay our clip in place and re-install our bolt. With that done we'll go ahead and turn our bar over here, remove the end cap, we'll then take and slide the block here into the channel. With that done we need to get our strip length. These will be included with your kit.

Thule Traverse Roof Rack Installation - 2014 Toyota Camry

Today on our 2014 Toyota Camry we'll be test fitting the Thule Traverse Roof Rack System using part numbers THLB50, TH480 and THKIT1438. With everything assembled according to the included instructions, we'll begin our test fit with the front doors open on our car. We'll place the front load bar onto the front of our roof and we'll need to measure 9 inches from the first part of the glass here at the front window to the leading edge of our foot pack. We'll need to make this measurement on both the passenger and driver's side of the vehicle to ensure the front bar is perpendicular to the roof of our Camry and the pads contour to the roof line. With the bar in position, we can use the included tensioning tool to tighten down the silver bolt on the inside of the foot which will bring the clips up tightly against the roof line. Now, we'll need to alternate tightening down each side a little bit at a time so the bar doesn't favor one side of the vehicle. Once that's tightened down and secure, we can place the rear bar onto the rear of our roof. We'll then need to measure the load bar spread.

Yakima Q Tower Roof Rack Installation - 2014 Toyota Camry

Today on our 2014 Toyota Camry we're going to be test fitting the Yakima Q Towers Roof Rack System using the 58" Round Bars. We'll use part numbers Y00409, Y00605, Y00716 and Y00124. With our rack assembled according to the manufacturer's instructions, we'll begin our test fit by opening our front door and placing the front half of our roof rack onto the front roof line. Per the Yakima fit guide we'll measure 8" from the rear edge of our windshield to the leading edge of our foot pack. We'll do this measurement on both sides to be sure we have our feet in line with each other. With both of our feet in line we'll now pull down on the black lever located on each foot pack to secure our clips around the underside of our roof line. With the front half of our rack secure we'll close our front doors, open our rear doors and grab the rear portion of our rack. We'll place it onto the rear portion of our roof.

Install: Yakima RidgeLine Roof Rack for Flush Rails on a 2014 Toyota Camry

Today on our 2014 Toyota Camry, we are going to be test fitting the Yakima Q Towers roof rack system using the 48 inch round bars. We'll use part numbers Y00408, Y00605, Y00716 and Y00124. With our roof rack assembled according the manufactures instructions, we'll begin our test fit by opening the front doors of our Camry and grabbing the front half of our rack. We'll place it on to the front roof line of our vehicle. For Yakimas fit guide, we are going to measure 8 inches from the rear edge of our wind sheield to the front edge of our foot peg. We want to take this measurement on both sides to be sure that we have our feet in line with each other. With our measurement done on both sides, we'll now pull down on the black levers which will tighten our clips around the underside of our roof line securing our rack to our vehicle. With the front hatch secure, we'll shut our front doors, open our rear doors and grab the rear half of our rack. We'll place it on to the rear portion of our roof.

Yakima Q Tower Roof Rack Installation - 2012 Toyota Camry

Today on our 2012 Toyota Camry, we'll be test fitting the Yakima Q Towers with Round Bar Roof Racking System, Part Numbers Y00409, Y00605, Y00716 and Y00124. Now, with our fit kit, our crossbars and our Q towers already assembled according to the included instructions, we'll begin our test fit by placing the front cross bar on to the front of the vehicle. We'll then measure from the first part of the glass to the first part of the tower. We'll measure this on both the passenger and driver side of the vehicle, ensuring that the front crossbar is perpendicular and the pads at the bottom of the Q tower are contoured to the roof line of our Camry correctly. Once we've established this position, we can then tighten down the silver hand bolts on the inside of the Q towers and clamp down the black lever securing the front crossbar to the front of the vehicle. We'll now place our rear crossbar on to the rear of our roof. We'll then measure the crossbar spread. Now, the crossbar spread is an important measurement when choosing roof rack accessories. The roof rack spread is the measurement from the center of the front crossbar to the center of the rear crossbar.

Thule Traverse Roof Rack Installation - 2012 Toyota Camry

Today on our 2012 Toyota Camry we'll be test fitting the Thule Traverse Roof Rack System, part numbers thlb50, th480, and thkit1438. Now with our feet, fit kit and load bars already assembled according to the included instructions, we'll place the front load bar onto the front of our roof. We'll then measure from the first part of the glass to the first part of the foot. We'll measure this on both the passenger side and driver side 9 inches. This will make sure that the load bar is perpendicular to the vehicle and the rubber pad on the bottom of the feet contour to the roof line correctly. Once we've established this position, we can use the included torque tensioning tool to tighten down the feet to secure it to the vehicle.

Fit Test: Custom DK Fit Kit for 4 Rhino-Rack 2500 Series Roof Rack Legs with 2011 Toyota Camry

Today on our 2011 Toyota Camry we're going to be test-fitting the "Rhino-Rack Roof Rack System." This consists of part numbers RRVA118B-2. Those are the "Vortex Aero Crossbars," part number RRRLKVA. Those are going to be the "Rhino-Rack 2500 Series Legs" for the crossbars. Then, part number DK114, that's going to be the clamp that attaches it to your actual vehicle. We have the front one installed already. As you can see, the bar has a nice aerodynamic shape to it. That is going to cut down wind noise and drag while you're driving.

Thule Roof Rack Review - 2011 Toyota Camry

Today on our 2016 Acura MDX we're going to be test fitting the Thule rapid traverse roof rack system. This consists of 3 different part numbers. We've got to start with our bar. This is the aero blade. Part number is THARB53. We've got our rapid traverse foot pack.

Thule Traverse Roof Rack Installation - 2010 Toyota Camry

Today, on this 2010 Toyota Camry, we are going to do a test fit of a Thule Traverse roof rack. Well be using Thule Traverse foot pack and a 50-inch Thule square low bars. We have our low bars pre-assembled according to the instructions, so Ill mount them up onto the vehicle and test them out. Well start off with the doors open and place the front low bar onto the roof. To properly position the bar, well measure from the trim edge of the wind shield to the leading edge of the foot pack. Always go by the instructions, in this case we will use the measurement of 9 inches.

Rhino-Rack Aero Roof Rack Installation - 2010 Toyota Camry

Today on this 2010 Toyota Camry we're going to install the Rhino Rack Roof Rack. Product number DA118 for the crossbars and DK114 for the clamp kit. For our quick test fit we went ahead and assembled the crossbars as described in the instructions and we'll just place them on the vehicle and see how it looks. We'll start off with the front crossbar. Let's lay it on the roof and we'll move it into its final position. To place the front rail we're going to measure from the center of the rail over to the center of the door jamb.

Thule Traverse Roof Rack Installation - 2008 Toyota Camry

Today on our 2008 Toyota Camry well be installing the Thule Traverse Roof Rack System using part numbers THLB50, TH480 and THKIT1438. Now weve already gone ahead and preassembled our roof rack system according to the instructions found within the fit kit so were ready to fit it to the vehicle. Well start by placing our front crossbar on top of the roof, well then measure from the windshield edge back on our roof 9 inches. This will be the location of the leading edge of the front crossbar feet. With our crossbar in place well open the door as the clamp will clamp to the inside of the door opening. We can then tighten down the two feet for the front crossbar using the included torque tool found within each foot.

Rhino Rack Roof Rack Review - 2006 Toyota Camry

Today on our 2006 Toyota Camry, we're doing a test fit of the Rhino-Rack Vortex Aero Crossbars. Part number for our crossbars today is RRVA126B-2. For our foot pack, we're using RRRLKVA, and for our fit kit, we're using DK028. Now we already have our front bar on. We've got one of our foot packs on our back bar, which, let me show you this last one and then how to install it onto your vehicle. The first thing we'll do is take our foot pack here, and we're just going to undo this bolt and set it off to the side. Now we can take our clamp, place it onto our foot pack, and then tighten down that clamp into that foot pack, just enough so that it doesn't slip out. That's going to stay in place there as well. Then we'll take off the bottom portion here, and we want this arrow to face out on the outside of the foot pack.

Yakima Q Tower Roof Rack Installation - 2002 Toyota Camry

Today, on our 2002 Toyota Camry, we'll be test fitting the Yakima Round Bar Roof Rack System using part numbers Y00409 for the 58 inch bars, Y00639 for the Q39 Q Clips for the Yakima Q Towers, and part Y00124 for the Yakima Q Towers Roof Rack Feet for the Naked Roof. With our Roof Rack System assembled according to the instructions, we'll begin our test fit by opening both front doors. We'll grab our front bar and place it on to the front part of our roof. To ensure that we have this bar in the correct location we need to measure nine inches from the leading edge of the windshield to the closest point on our foot pack. We'll do this measurement for both sides of the vehicle to ensure that our feet are in line with each other. Once we have this set, we can use our thumb screw to snug our clamp to the roof line of our vehicle.

Thule Traverse Loadbar Installation - 2002 Toyota Camry

Today on our 2002 Toyota Camry, we'll be test fitting Thule Traverse Roof Rack System using part numbers THLB50, TH480, and THKIT1261. Withour roof rack assembled according to theinstructions, we'll begin our test fit by opening our front doors. We'll place our bar onto the front part of ourroof. We'll make sure that thepads are fitting correctly and then we need to take a measurement to make sure we have it in the correct location. Weneed to measure 9-1/4 inches from the leading edge of the windshield to the closest point onour foot pack. We'll do this measurement on both sides of the vehicle to ensure that our feet are in line with each other.