Most Popular 500 lbs Vert Load for Ram 2500

This receiver hitch fit my 2015 Ram 2500 fine, and looks good. However, Draw-tite quality control must be a bit lax, as now that I tried to use it, I find the hitchpin holes are not the same size and even a standard pin cannot go through both holes (so as is, I cannot use the now-mounted hitch). I am going to have to bore out the hole(s) to the correct size for a locking pin, to mount the hitch-mount winch I intended to use in my dump trailer and my truck. In addition to being the wrong (or mismatched) holes, the location of the holes is right next to a beefy weld that will make securing (whether by locking or non-locking hitchpin) difficult. I cannot justify removing the receiver after all the work it took to install, but definitely cannot give this a good review. I recommend test-fitting your pin(s), tow balls, winches on it before you waste time installing. However, as always, etrailer.com rocks!

I have always wanted a front bumper receiver but always resisted because I thought it would require welding, this unit is bolt on and went on my Ram 2500 with no problem at all, it looks like it was factory installed.

This hitch is perfect. It's great quality and it bolted up easily. Took me just over 1 hour to install.

Fit properly. Works well for designed purpose. I'm using it for a SnowSport plow. I tend to hit the stacked pile too hard and have bent the Curt Front Mount Trailer Hitch Receiver. The receiver box was pushed backward and tilted up. The up-tilt lifted the plow too high to work by the end of last season. The plow is putting a lot more than 500 lbs load on the receiver. I'm way beyond designed specs. I don't blame the hitch. I blame my inability to hold back on pushing snow taller than the hood of my 4wd RAM 2500. It was the only way to stack enough snow out of the way to get through the season. I've had it cut and straightened, mostly. It's working for this season, but fixing the bends cost what I paid for the hitch in the first place. If it bends again this season, I'll probably add some 3-4" x 1/4" plate to the top and bottom of the cross tube to reinforce things.

Fast shipping, good quality and very easy to install. Total time was 30 minutes. Bike rake sits in receiver has very title movement.

I had reviewed the installation instructions online and had removed the bolts and trimmed the fascia before the hitch arrived. I used giant heavy duty zip tie to tie one side up close to mounting point and the raised and maneuvered hitch into place. Then installed the bolts. Did this by myself. Hand tightened bolts, then used jack on receiver to get it to sit as high as possible and then tightened the bolts. Installed my Young Electric Mate R bicycle rack on it. Works perfectly!

The fit was a bit too tight but we were able to make it fit. The shipping packing was pretty lacking. Since being installed we have been using it with a spare tire mount. That works great and it makes the spare tire more accessible compared to the standard under the bed mounting. When fully loaded with a camper and towing a boat moving the spare tire to the front improves the weight distribution.

Curt actually recommended that we use etrailer. They even gave me the confirmation that the hitch would work and told us you have a video. Thanks!

This hitch is definitely heavy duty and mounts securely. It does not block airflow to the radiators or interfere with the bumper proximity sensors. It deserves 5 stars from that perspective. But I give it 4 stars because unfortunately the distance between the side plates was 3/4" too narrow to rotate into place. It would not clear the frame rails, brackets, and spacers. Actually it wouldn't even clear the frame rails alone. My son and I read the instructions many times and experimented with every possible angle (which is a major hassle while supporting the hitch under the truck) and finally took the matter into our own hands. We used a high lift jack situated between the side plates to bend them outward. Then the hitch fit perfectly. Getting the bumper lined back up was another headache, but not because of the hitch.

Seems nice and solid, should be strong enough to haul my 425lb motorcycle + 60lb carrier. Based on some of the reviews about what a pain it was to install I decided not to mess with it and take it to a hitch shop. They confirmed some of the complaints I read here so it was money well spent.

I purchased this front receiver hitch for my 2010 Ford E350 RV to use for a utility basket, launch a 16' boat and now also for a motorcycle carrier. The quality is excellent and full weight rating, one year later and the finish is perfect. Installation was exactly as stated in the directions and the modifications were minor, requiring existing holes in the frame forward of any critical mounts drilled larger and the plastic under the front bumper where a tag goes has to be cut slightly to allow for receiver. The directions called for removal of under carriage splash guard but I was able to trim and reinstall. I am perfectly happy with the purchase. When hauling a motorcycle on the front the RV rides so much smoother and better planted on the road without being overloaded.

Have been an e- trailer Cust for most of my hitch and trailer needs for years. The RAV4 hitch and air bags have been a real plus cause the Mrs uses it like a mini truck. The hitch attachments and extensions we’ve bought all top notch - expect nothing less from this front mount hitch for our c class Rv. Recommend you always check with them first before buying elsewhere.

Great products, great prices, fast shipping and a great company to do business with. Easy install, and it took longer to trim the air dam than installing the hitch.

Great solid piece, as you would expect. Extra longer bolts are included in case you have the factory tow hooks, a nice touch and saves $10 at the hardware store. Not a complaint, just info; you have to remove the bumper to fit the front bolts, they won't drop in past the bumper brackets at least on my '95. Cut a hole and some minor trimming, and it works with the factory air dam as well.

This front receiver mount is exactly what I needed. Great build quality and easy to install. Thanks for getting it to me in a timely manner.

After a year of having this on my truck I can say that I wish I did it sooner! The installation is easy as can be. The hitch is super handy as both a tow point and also as a kind of skid plate/bumper. I have contacted multiple ecology blocks and other objects in my truck, the hitch is the first thing to touch so nothing on the truck gets damaged! This is a super strong, affordable, and versatile addition to any vehicle!

It is a great hitch I have a front rack that’s on it now to haul my generator and fire wood also I’ll be using it for my bike rack to haul my e-bike with , did lose my mind on the bolts I did get some help to get them in,tho my patience ran out, but all in all it’s a great hitch.

Added to use with a front winch. The install was not too difficult and the included instructions were spot-on. On my F250, the front tow hooks add to the strength of holding the hitch to the frame. On the F250 you do lose the OEM fog light location, but I used the wiring to add/relocate after-market fog lights. The set up has already proven helpful, pulling me out of a snow back while plowing. Just what I needed for some summer off road camping as well.

2nd hitch, both fit up great. Left off the roll pan and built our own cover for the sway bar disconnect.

I bought this receiver to add front mounted 'accessories' on my 2007 Jeep Wrangler Unlimited Sahara. I plan on using this to add an extra bicycle rack, a cargo basket, a receiver mounted winch or other 'accessories' needed for my Jeep when I take my family camping. It will also be useful for "front launching" a boat or parking a trailer in tight spots. It took me about an hour to install, although I had already previously removed the lower wind deflector cowling, so did not have to spend time removing it or cutting it for a finished look. Detaching and moving the top trim panel between the grill and the bumper is a must to facilitate the installation. The receiver fits pretty close, although you do have to manipulate it to get the holes to line up with the frame. Follow the instructions and do not tighten any of the bolts until you get it lined up and all the bolts in loosely, then torque it down. As noted in the instruction sheet, the driver's side of the receiver does not sit flush against the frame, there is about a 1/4" to 5/8" gap. The instructions say to use the extra split washers (in the kit) as filler, but they would just rattle around loose in there and provide any benefit, so I omitted them. Once tightened down, the receiver tube was not parallel to the ground, it is slightly higher in the front, sloping towards the rear. It is not off enough to affect my intended use, but may be bothersome to those with type 'A' attention to detail. Overall a good product that will add a lot of flexibility to my Jeep~

Appears to be a solid, well made product. Had a slight bend to one of the mounting brackets that looked to have occurred during shipping, easily corrected. All the hardware was included and appears to be sufficiently sized. Included instructions were clear and well written. The product was actually delivered ahead of scheduled date and the total price was reasonable. Well satisfied thus far.

It was a bit harder to put on than they show in the video. Did it by myself, everything fit perfect SO OWSOME! I would recommend anybody. Truck or car should add one. Very convenient and can be use for many different purposes.the rack on the back, I now put in the front with generator gas tools and it works as steps. So now I can tow trailer, or jet ski. Having that front hitch is so cool. You could even attach a car whinch in the receiver.

After struggling with the answering menu, Steve Z. was instrumental in locating a hitch to fit my van which was not specifically identified in any data search. Weird year, 2005, of popular Chevy Express van, my luck! Using manufacturers dimensions I purchased #31016 on 12/21 and it arrived on 12/24. It's a very well built, USA built, unit. It arrived rapidly, but was missing half of the mounting hardware. The remainder of the hardware was rolling around in the box. Zip lock baggie ripped apart spilling them. I used a hydraulic jack to elevate hitch into place, and an additional jack to push the drill up to drill the 6 mounting holes necessary. No factory hole alignment. All the nuts for the bolts were lost in transit, but by a Christmas day miracle, I found 2 metric nuts to fit supplied bolts that survived the delivery. I will acquire, and install remaining missing 4 tomorrow. The installation went smooth and easy using this technique. It took around 3 hours with much of the time searching for hardware.' Thanks Steve Z. and etrailer. .

The product works great. However, I was told that this front hitch receiver would bolt to existing holes on my 98 Four winds RV. That was not true, so installation was double the cost of what was estimated by the shop I took it to.

The front hitch solved a storage problem that I was having with my truck camper.It fit perfectly. I added a Stow Away hitch frame and a UWS small aluminum storage box for my small generator. The photo shows a test fit before installation.

This was one of the easiest accessories I’ve installed on my Tundra. It is a front receiver hitch so I don’t use it very often. Mostly just for bike racks when towing a trailer, but when you need it you need it.

This worked great on my F350 dually. We needed a front hitch to carry bikes while towing a 5th wheel camper. Instructions were easy to follow

This appears to be a great receiver hitch! The first one arrived bent because UPS employees threw or dropped it. e Trailer was fabulous in getting another one out ASAP. Assembly and fit was great as well. The only recommendation I would make would be to provide a template with measurements to cut the front rubber air damn to ensure a factory finish.

This front-mount hitch works great for putting travel trailer into tight RV Garage (West Coast Metal Building). I don't have a straight shot into the garage, and trying to back the trailer into the garage is do-able but takes many, many tries. This hitch makes it easy to maneuver the trailer while facing forward in the truck. Since the front hitch receiver is relatively low to the ground, I needed to get a high-rise ball mount. The riser part of this interferes a little but with the truck's under-bumper flexible fascia, but does not damage it. I also purchased a 2" black rubber hitch receiver cover (plug) to keep water out of the receiver. One thing - be careful when pulling up to parking lot curbs. Ground clearance of this hitch is relatively low and I have hit a couple of curbs with it. Thankfully the hitch itself and the mounting points on my Ram 1500 are very strong, and no damage was done other than mangling the rubber hitch receiver cover a bit. Note: I built a wood frame to support the hitch during installation, since I did not have a helper to hold it while installing the attachment bolts.

This front hitch receiver for my 2016 RAM 1500 works great! The installers did not have to cut the facia under the nose of the truck. The hitch fits tight against the facia, but no cutting needed. They did have to drill some holes, but I used professional installers, so I'm not worried. This finally solves my problem of not having anywhere to mount my two bikes while towing my 23' camper. The options for camper bike racks don't work for us for several reasons. Glad I can take my bikes with me on my Saris rack. I purchased an adapter and pin to allow my 1 1/4" bike rack to fit in the 2" receiver. I also purchased the hitch receiver cover separately.

This product DOES NOT fit a Ram Rebel as described in this answer: Significant modification of the hitch and/or bumper valance panels is necessary to get it to fit. Please update the answer linked above.

I Installed a Draw-Tite front mount hitch on a 2019 Ram 1500, Big Horn, Gen 5 (not classic). The hitch tube comes to 1/2" below the front bumper and is set back under the top edge of the bumper/airdam. The cutout in the airdam started 3/4" from the top edge and about 3" long and stopped right before the bottom curve and cut 3" wide. This fit with about 1/16" clearance on each side and top to bottom was perfect with no visible gap. I used a Dremel Oscillating Cutting Tool with a flat blade to cut the hole in the airdam and to cut out the notch in both of the airdam supports. Using a razor knife to cut the hole would be very difficult. My install time was about 3+ hours (no lift) lying on my back and the hardest thing was getting 2 of the mounting bolts torqued to 115 ft. pounds. This also required 2 people to install the hitch and reinstall the OEM Splitter. I do not have OEM tow hooks, so I don't know if the hitch would work with them installed. I purchased a MaxxTow Tow Strap Loop for 2" Trailer Hitches - 10,000 lbs - MT70029 to use as a pull point for my tow strap. etrailer was very fast with shipping, 3 days, 5*****.

UPS was 8 days late for no good reason though it looks like they used the hitch as a crash test dummy. It’s a miracle the hardware bag made it but it did! I think this is superior than the other brands available. They always include these little threaded fish tape wires for getting the hardware into the frame. I’ve done a transit and now this. Saves a ton of time/headache. However the instructions just have a diagram. Took me about 20 min to get the first bolt in. Then 20 min for the rest of the install. So if you read this, you can probably get the whole thing done in 30 or so which is what i expected initially. Tools: 3/4” socket Torque wrench 1/2” drill bit & drill OPTIONAL: floor jack to lift hitch into place. Steps: - Drill forward holes to 1/2” and shoot with some rustoleum or equivalent paint. Let dry for 20 min while you eat lunch, take a dump, whatever. - send fish tape through forward mount hole and out front of frame rail. Figuring this is what slowed me down on the first one. the carriage bolt head won’t fit through any of the obvious openings. See pic. - put to bolt plate onto the fish wire then thread the bolt onto the wire. Pull em all through the hole and watch it assemble right before your eyes! - repeat on the other 3 bolts - jack hitch into place and finger tighten the washers/nuts on - torque down to 75ftlbs and boom! time to yank or be yanked! See all my pics and if this helps, send me an imaginary beer through the quantum field! Econolines rule!

I tried ordering this exact hitch off Amazon. Not once, but twice they shipped the wrong part number. Took a couple months to get my money back. Etrailer got it right the first time. I took about an hour to install on my 2006 class B+ E 450 motor home. The best advice I can give is take the 15 minutes to remove the front bumper (21 mm). With front bumper removed you won't need the wire chaser things. Jus stick your hand in the frame.

Mounting went well,video direction were accurate.

Overall, my experience with etrailer was good. There was an initial delay in shipping, but once I talked to someone, everything went well. The help page was invaluable. The biggest help was the installation video. While there are slight differences between the 2011 GMC and the 2013, the process was the same. I am very pleased with the product and the support. Picture attached.

This has been a great purchase that has enabled me to maneuver my trailer better in the space I need to park it in my backyard off a fairly narrow alley. I installed it on the front of my '98 Dodge Ram 2500 4x4 V10. It is stout and secure and was not too difficult to put on. I think most of my installation issues were factors of my truck's age, or mine, but who knows. As I recall, I had to attach bolts in a particular order so that the holes would line up right and I wasn't sheering the threads. After I figured out the order it snuggled up great and feels as solid as if it were factory installed. My front plate bends a bit at the bottom to compensate for the receiver sticking out, but no so bad as it isn't readable. It does not stick out much more than the bumper so I have not run into it when walking across the front of my truck. I love it to push my trailer in to my yard and I can't wait to put a boat in the water with it. I would buy one again, if I were to ever get a different truck...but why would I do that?!

My front mount receiver hitch for my 97 Dodge Ram came in perfect shape and in a timely manner, the installation went very smooth and instructions were very easy. Only thing I recommend is a little longer sway bar bolts would be nice, just a little hard to get started. Other than that perfect easy company to work with and shipping was great I will be using etrailer for future purchases thank you!!

We chose the Curt Front Mount Trailer Hitch Receiver so we could safely transport our RAD electric bikes while also pulling our travel trailer. We had it professionally installed onto the front of our Toyota Tundra and it has worked out very well! We are very pleased, and glad that we have it!

Shipping was fast and packaged good with no scratches. I modified my 2010 Tundra skid pan for oil filter changes before mounting. Replaced all 4 OEM tow ring bolts using anti-seize with new longer M12-1.25 X 40MM class 10.9 zinc finished hex cap screws along with new M12 X 24MM OD HARD WASHERS and torqued all 4 to 79 ft/lbs. Mounted new Thule EasyFold XT 2 Hitch Bike Rack and it fits in front without using the hitch extension. All went together as planned and can now take E-Bikes with us while pulling our camper. We are happy campers!