Best Keystone Bullet Premier Ultra Lite Travel Trailer Camper Jacks

My Jack arrived DOA. After installing it on my trailer, the Jack didn’t work. The manual crank handle came in handy because I didn’t have time to troubleshoot and repair it at the time. It was just a wire that was no longer connected to the switch but I have to tell you it was extremely disappointing to receive a brand new item that didn’t work. If it had worked out of the box, I’d give it a five star review. You should consider soldering and heat shrinking the wires to the switches or making the wires longer so they aren’t banjo string tight and putting the lug at a strange angle.

Great product and Trailer has great customer service. It's to bad that the shipping companies do not take better care with the items during shipping! will receive replacement parts to fix what was broken, but it causes lots of extra work for the customer. will have to take complete jack off to replace the broken motor cover because of shipping carelessness!! regards, Dan Ewert

I purchased this jack to replace my tired 10 year old camper jack . I ordered it at 10:00 AM Monday and as promised by Ian it was at my doorstep on Friday just in time for my weekend getaway . Installation was a breeze . I gave the product a 4 out of 5 for a few reasons . First , I was not able to see the manufacturer of the jack before receiving it . Which made name brand comparison pricing difficult . However I feel pricing was on target . Second , I feel that the jack should come with a battery terminal end connector and new mounting bolts with the hardware that was included . This didn’t pose any difficulty to me as I had hardware at hand but for some it will mean a trip or two to the hardware store . Third , once installed , at least with my truck and trailer , unless the truck and trailer are perfectly aligned and level the jack motor gets in the way of opening the tail gate . On first use I noticed it was much slower than my original but the strength made up for it . This jack had no difficulty or hesitation lifting my truck and trailer for load distribution and anti sway bar installation . I would recommend etrailer and this product . Time will be the final test of its durability .

Item arrived a day earlier & in good condition! & was a very easy install ,& is a upgrade from manual one that broke at the handle ,& this is a upgrade for my 2008 22'Airstream Safari! Can't wait for my next outing, Also I like that it comes with a backup manual hand crank in case you need it,& that it was a exact fit for my travel trailer,It's a complete package that needs nothing else.

Replacement for bent camper stabilizer jacks, these work great.

Very solid and well built, exceeded my expectations. Mounted tonight and the camper is now solid as a rock when parked. It only had rear stabilizers previously and at 19 feet needed the stability in the front. Wifey says previously it felt like she was on a water bed when I was walking in the back. Not any more!

Order Thurs, delivered Sat 2 days ahead of schedule. Box in good condition. All parts present. Instructions clear. Replaced 3 yr old jack (locked up). Found lower price by $20 on Amazon, chose etrailer instead for the videos and hometown presales customer service people like Kimberly. Worth the extra. Can't always be about the green. Made sure to scrape paint of all surfaces as per instructions for the ground. Installed day of receipt and works great. Looking forward to the 1, 2 and 3 year hopefully positive reviews.

Put this jack on the trailer tongue in less than an hour. Moves the tongue of a 29' 6500 lb travel trailer up and down easily. I did not find it particularly slow. Install tips: I used a two ton bottle jack and static jack stand to support the tongue while working. Check trailer negative grounding with a voltage tester, just to be sure you get a good circuit. I attached power cord via fuse directly to positive battery terminal and stowed the extra wire/fuse in the battery box. (My trailer has a power line and blade-fuse from the trailer's junction box for the previous jack but it had an occasional short so I didn't use it. If your trailer has a dependable powerline for a jack, use it.) I'm putting a 10L dry-sack over the powerhead to keep out rain, road dirt and bugs. An extra layer of protection never hurts. I hope this holds up better than the factory installed L*****t. I'll write a follow up review in a year or so. And as always, thanks etrailer for great service, great prices, and fast shipping.

if I had to rate this upgrade in difficulty one being the easiest five being the hardest, it would be a one. Super simple. Take the nuts and bolts off your old hardware and install the upgrade in its place. I read some of the reviews were people were annoyed with the counter clockwise rotation and the bolt sticking out too far. I really didn’t see a problem with either. I know you’re not supposed to use a drill to extend and retract these but I always have. I suppose as long as you’re not torquing the heck out of the adjustment screw you shouldn’t have any problems. I always put a small flat 2 x 6 piece of wood under the foot of each one of these. It seems to add quite a bit of stability.

The jacks themselves have worked great, they keep the trailer level and solid during our concession events. I just had them mounted to the trailer so I don't have to put them in and out at each event. The jack handles leave a bit to be desired so I use a 20v drill w/ a 3/4" socket to run them up and down.

Works great as a stabilizer. I have a 38' trailer and I use screw jacks to level the trailer. Once the trailer is level I lower the stabilizer jacks to eliminate any movement. With this combination the trailer does not move one bit.

There's not a lot to say. The first Stabilizer carton was damaged to the point the carrier couldn't even find the Stabilizer. etrailer.com was very cooperative & sent a second unit out right away. Although the second shipment packaging was damaged all parts were there and undamaged. I installed the unit and it is so so much better, quieter and faster than the old unit. I highly recommend both Lippert and etrailer.com

This is what I needed. I Wanted a little more lbs. of lift so I could lift my truck for weight bars and such. I have a 2014 Rockwood A Fram and needed the mounting holes to line up. After some research, I found Stromberg jet-3755 worked perfectly. I have used it for a year now and no problems. Easy to set up and use. Thank you etrailer

Item arrived a day early. Installation was easy. Jack works smoothly. 3500# rating is 500# better than the factory installed jack.

Great product. works just fine. The problem I had was matching the mounting plate under my trailer. Apparently not a standard so I had to take it to a trailer manufacturer to make it fit.

They went on a custom made trailer build that’s not yet in service. Seem to function as advertised.

One small part was missing from my Ground Control TT. Carol Korren expedited delivery of the missing part and the UPS truck pulled up at the moment I needed the part. Fantastic customer service!

This works great and has been the very best upgrade on any RV/Trailer I have every owned. I will never own another trailer that does not have this.

The powerhead is very large and extends forward, which has caused it to impact upon two different vehicles when backing the trailer. The power function is now useless, and I am using the manual crank to raise and lower the jack.

Sturdy jack, easy to install. We installed it facing to the driver's side so we can still put our tailgate down. Very powerful jack, only drawback is it is very slow.

Took the sway out 95%. Excellent customer service! Quality product.

Before I purchased the Strong Arm my travel trailer would shake considerably when someone would move around the trailer. Since installing the Strong Arm system (which was quite easy to do) movement about the trailer is no longer an irritating issue.

Ordered a power stabilizer jack for my 2012 Jayco fifth wheel in 2023 , easy to install the item myself , stabilizer working great , will buy future items at this site , thanks

The stabilizer works well. I would buy it again

The product works as designed. Easy to install and I have used it approximately 20 times in the last year. The storage for the 7 pin connector and safety chains are a great option. Keeps things nice and tidy when unhooked. I highly recommend this Jack.

Perfect fit and operates very quietly and with abundant power for my 27 foot Lance travel trailer. The Jack-It Lippert bike rack mount fits perfectly over it, and the manual emergency jack crank fits within the tube of the Jack-it if the need arises. Also, the handy ring for stowing the trailer chains and receptacle for stowing the 7-way connector is a nice feature. Very happy with my purchase, and etrailer is fantastic, as usual!

Customer service from e-trailer has been top notch both times I purchased from them. I highly recommend this company for your travel trailer needs.

Works great for my teardrop

Quick shipping. I will be ordering more parts as I need them for our RV.

We replaced four badly worn 2500 lb jacks with these heavier 5000 lb jacks and are very happy with the quality of these new jacks. They arrived quickly and were a perfect fit. The construction is superior to the jacks we replaced. Your instructional videos were very helpful. Thanks for your excellent service.

Installed jack on trailer, tested with a battery. Works great, it will lift my cargo trailer high enough for my 3/4 ton Ram. In the past have had to carry 3 blocks for the screw jack, now only a small one just to keep the steel jack pad off the cement or ground. Have not wired the new jack yet, we still have winter here in ND and will not use it until the end of April. The jack, I believe, will work fine. I forgot to order a cover for it when I ordered the jack, just did that this morning. Thank you etrailer.

The jack works great. I didn’t have any problems with the installation. My only issue is that the holes are 90° off for my Fastway jack foot which goes up automatically. I’m debating whether to leave the jack 90° off or drill new holes in the jack.