Best Ford F-250 Super Duty Front Receiver Hitches

This worked great on my F350 dually. We needed a front hitch to carry bikes while towing a 5th wheel camper. Instructions were easy to follow

This appears to be a great receiver hitch! The first one arrived bent because UPS employees threw or dropped it. e Trailer was fabulous in getting another one out ASAP. Assembly and fit was great as well. The only recommendation I would make would be to provide a template with measurements to cut the front rubber air damn to ensure a factory finish.

Excellent from researching, ordering, fast shipment! Years ago I purchased a front hitch for my 2008 F-350 from etrailer. It was a no brainer to buy for my 2024 F-250. The videos make installation a breeze. Thank You

I put this on my 2022 F450 so I can carry a bike rack while carrying my slide in camper. Overall fit was great and the video on this site was very helpful. I did have to slot the brackets on the auxiliary cooler about 1/4" with a file so it could sit up higher so the hitch wouldn't put a lot of pressure on it. After that it all fit together nicely.

Plastic trim that direction stated to be trimmed were not even close. Had to majorly trim plastic in bumper center section. Other than that it was straight forward

Just what I wanted. Been wanting to get this and install. Pretty straight forward for my boy and I. Took about 2 1/2 hours. Hardest part was the cutting of the plastic and marking everything but we got through it. Only thing wrong the license plat bracket was welded crooked, I don’t need it was going to run so it’s hidden. Could not ocd got me.

Works great for hauling our bikes. Hitch was easy to install and easier on a lift. Quality product and service from etrailer. I did have to get an extension to get bike rack past the bumper (Ford truck).

I went with this hitch since I have an after market front bumper. I wasn’t sure if it was going to fit but since this hitch was a bolted connection it gave me 2 options to have a chance it would fit. One I received the package the box was damaged but all the hardware had been taken to the hitch, so everything was there. I installed the hitch by myself and took me about 2 hours but that was due to the aftermarket bumper and dealing with that hardware at the same time otherwise the install went smooth. Tha last phot is to show this hitch worked with this bumper.

This is the second front hitch receiver I have installed from Etrailer, and I am just as impressed with this purchase, as I was with the previous one. One thing to note: the product states is not compatible with the brush guards, and that is not accurate. It was very troublesome to lineup both the brush guard supports, and the receiver supports with the frame. But it is doable with patience, an extra set of hands, and colorful use of the adult language. (installation w/o a brush guard was a cake walk) I had my previous front hitch on an F150 for 5 years, and have had this one on my current F250 for a little over a year. They hold up very well, provide versatility to haul loads on the front of the truck, so you can fully utilize the bed, or tow a full trailer. This is now the first modification I suggest to new truck owners.

Let me start by saying this is not the first front receiver I've purchased from etrailer all my trucks get front receivers for winches. This time though the box shows up on time but the corner is blown open and the receiver is hanging out. Also the bag of bolts has been ripped open and half the bolts are loose in the open box but to my surprise after counting everything, they were all there.spray foam packing would have mitigated all that. Moving on. Went to install the receiver and the end mounting plates are 1/4 inch too tight. Won't fit the frame rails. Had to spread each side 1/8 out with a Hydraulic bottle jack. Apparently using a jig during the manufacturing process is optional these days. After all that I finally got it to fit good. It looks good and the welds seem adequate. I think it could have been installed in an hour by myself if not for having to "adjust" it but was still done in under 2 hours.

It is a great hitch I have a front rack that’s on it now to haul my generator and fire wood also I’ll be using it for my bike rack to haul my e-bike with , did lose my mind on the bolts I did get some help to get them in,tho my patience ran out, but all in all it’s a great hitch.

Added to use with a front winch. The install was not too difficult and the included instructions were spot-on. On my F250, the front tow hooks add to the strength of holding the hitch to the frame. On the F250 you do lose the OEM fog light location, but I used the wiring to add/relocate after-market fog lights. The set up has already proven helpful, pulling me out of a snow back while plowing. Just what I needed for some summer off road camping as well.

The fit was a bit too tight but we were able to make it fit. The shipping packing was pretty lacking. Since being installed we have been using it with a spare tire mount. That works great and it makes the spare tire more accessible compared to the standard under the bed mounting. When fully loaded with a camper and towing a boat moving the spare tire to the front improves the weight distribution.

Curt actually recommended that we use etrailer. They even gave me the confirmation that the hitch would work and told us you have a video. Thanks!

I ordered these two, front and rear for a 1990 GEO Tracker 4 wheel drive that I am rebuilding. I believed they would fit, I finally got around to mounting them and they don't fit, to large. I think I have had them to long to return them.

Hi George, I received your email and didn't realize it had been a year already. I'm afraid I don't have anything to say that you want to hear but I will tell you anyway. I spent about a week researching this hitch and read numerous reviews about it and how easy it is to install with installation times of 30 minutes to an hour, so finally I bought one. I read the instructions when I got it, looked simple enough. I've been building cars and motorcycles most of my life, a few hot rods and drag raced Harley's for 8 years, and I had to fabricate a lot of parts on the drag bike splus I've been a CNC Machinist for 30 years, and having just retired this project was on my list of things to do NOW! Well its been a year and the hitch is now sitting in the corner of my dining room. Either I have a Jeep Cherokee that is an odd ball or its just my crappy luck. In the directions it says to use the fishwire for putting in cm-sp1 and the bolt. I can supply pictures if you want but there is no access hole anywhere near big enough to get the sp1 spacer in the frame and the end of the frame isn't open either as the directions suggest. Apparently its either butcher the frame with a hole big enough to these spacers in, which I really don't want to do, or try to sell the hitch for whatever I can get and say the hell with it, except I really need that front hitch. I realize most people are very happy with your product, but I'm sorry to say I'm not at all. You asked!

I own two of these hitches on two different trucks. One hitch has been in use for 6 years. The other one is a year old. The older one has functioned flawlessly. The new one went together well. The only issue is that one of the self tapping bolts broke off even with the anti-decapitation bar. It's not a huge problem, however I will have to remove the entire assembly to re-drill the broken bolt out which will damage the threads, requiring larger bolts. Looking for grade 8 3/8 or 10 mm self threading bolts as replacements, which may not exist? Another thought is to drill all of the way through both sides of the antidecapitation bar and use nuts and lock washers. The hitch is great otherwise!

Unfortunately the item I wanted wasn't in stock at etrailer, but I had time before I wanted to install the item, a front mount hitch. The vendor was on time with supplying the hitch and etrailer shipped the hitch in a timely manner. It arrived yesterday evening and I installed it today. I've installed three front hitches, all from etrailer Curt and Draw-Tite I believe over the past few years. Two this year. The first picture is the front hitch on a 1998 E-450 class C motor home, the second picture is on a 2002 Ford F-350 pickup truck.

I use Curt Front Hitches from ETrailer with pintle hitch plates to make my own front protective bars and also rear protective bars in a rear truck, SUV. Or van hitch to protect my vehicles from bad drivers. Much stronger than bull bar or offroad front bumper bar protection

We live just south of Buffalo and Put this on our '11 Honda Ridgeline with a snowsport plow and a week later it snowed, and snowed and snowed... 5 feet in 24 hours and it's still snowing.... It's not good.... It's AWESOME! Not one driveway or even our street is clear... Except ours. It was easy to put together , easy to install and works exactly like it's advertised! It's November and it paid for itself already. Communication with etrailer was exceptional. We could not be happier with the whole setup.

This front receiver mount is exactly what I needed. Great build quality and easy to install. Thanks for getting it to me in a timely manner.

After a year of having this on my truck I can say that I wish I did it sooner! The installation is easy as can be. The hitch is super handy as both a tow point and also as a kind of skid plate/bumper. I have contacted multiple ecology blocks and other objects in my truck, the hitch is the first thing to touch so nothing on the truck gets damaged! This is a super strong, affordable, and versatile addition to any vehicle!

I had problems with your website but etrailer corrected my issue. I’ll look forward to ordering again.

This is the second front hitch I have purchased from etrailer. As with the first, this was a well built, solid product. It fit my older 2009 Ford Super Duty perfectly. The only thing that was incorrect was in the instructions it called out the tools needed. But the actual sockets needed were larger than called for. Not a big deal, but something to correct moving forward. I mounted the hitch myself in about 45 minutes. Most of that time was getting set up and going looking for the larger sockets. I used a roll around jack, as I did with the first hitch, to lift it into place and be able to move it around. Works well. Everything was A+. Sorry I have no pictures. But it looks great.

Perfect hitch for those needing a rack for extra space. I used a heavy duty vinyl bag to enclose my tools, cords and generator on my 12k mile trip to alaska. The held that 500lbs extremely well across the permafrost damaged Alaskan highway! No twists, no bends and no worries!

Looks great

Requires permanent removal of the front air dam. Requires temporary removal of the front sway bar. May decrease offroad performance by lowering the approach angle. Has 2 Sturdy retrieval loops.

I chose Draw-tite because they are built very well and this one is no different. The welds are done well and I have no fear that this product will serve me well. The install wasnt to bad for a DIY type like me and the fit was excellent, only took a few hours. Knowing that I can now be pulled out of a bad situation or pull someone else out is comforting with the help of a hitch mounted winch. The Price was right and etrailer shipped it out fast although packing could use a smaller box . Oh yeah, UPS sure tested the toughness of this receiver ! . Great product and great service from etrailer

Super easy to install product thanks to the video! Took all of 25 mins to install

Great product,easy installation and dealing with etrailer has been a real good experience.

Review for truck front hitch receiver I finally Installed the front receiver hitch today, I pulled it out of its package and found all parts wrapped to the receiver hitch good call as there was a hole in the box. The license plate holder received some damage it was bent some. Installation. I reviews the video prior and read the instructions. Had to purchase a 4 inch hole saw and a torque wrench that added to the cost of the hitch. Installation was for the most part straight forward, when the video cuts from shot to shot I now know all the cussing and swearing are done during that time as it’s very difficulty to get the hitch in over/under the exiting hardware, solo installer took me 3.45 hrs to install, tight fit under the truck to maneuver under the truck. Bolts back into original tow hooks was a total Pain in the A$$ trying to hold up the hitch and the hooks while trying to maneuver the hold back in. (Had to take it out as I inserted on the wrong side) I will say that installation is doable by novice front yard mechanic but with a difficulty of 7 out of 10, trying to get the bolts torqued to specs is difficult due to clearance and angle of the bolts. Make sure you have deep well sockets because the new bolts for the hitch and long and a standard size socket will not be able to grip the nut as you tighten it down to specs. Put the bike rack on the hitch receiver and found that the hole that we drilled out to put the hitch in is not big enough. The bolt for the hitch goes in from the right and there was barely enough room to get it in the hole, used a wrench to tighten it but it was slow going, the other issue was that on the left side there is a hitch lock I struggled to get it on, but then could not reach in to remove the key. So final outcome was I had to drill out another 4 inch section of the bumper to get to the key. If your hitch has a bolt on bike rack like the swagman e-bike rack you want it to be secure so the bolt is a must this option may not be the best option. The bikes block the headlights so no night driving with the bikes on the rack. The handlebars need to be folded down otherwise the bikes will ride too high on the front and obstruct your vision. If I had to do it again I would have gotten the hitch that is lower and would not have to drill out my bumper, and it would have given me more visual clearance. I did take a shot drive with the bikes in front it will take a bit to get used to them being in the front as well as making wide turns while towing the RV that I don’t take out the car in front of me.

It was delivered on time in 2 days. The installer mentioned that it was packed very well in a nice box. It is strong enough for various uses. The magnetic Lic. plate holder covers the hitch when not in use, you would never know what's hidden behind it. I used it for a bike rack this weekend and will be using it for a cargo platform next.

Great products, great prices, fast shipping and a great company to do business with. Easy install, and it took longer to trim the air dam than installing the hitch.

Great solid piece, as you would expect. Extra longer bolts are included in case you have the factory tow hooks, a nice touch and saves $10 at the hardware store. Not a complaint, just info; you have to remove the bumper to fit the front bolts, they won't drop in past the bumper brackets at least on my '95. Cut a hole and some minor trimming, and it works with the factory air dam as well.

This front-mount hitch works great for putting travel trailer into tight RV Garage (West Coast Metal Building). I don't have a straight shot into the garage, and trying to back the trailer into the garage is do-able but takes many, many tries. This hitch makes it easy to maneuver the trailer while facing forward in the truck. Since the front hitch receiver is relatively low to the ground, I needed to get a high-rise ball mount. The riser part of this interferes a little but with the truck's under-bumper flexible fascia, but does not damage it. I also purchased a 2" black rubber hitch receiver cover (plug) to keep water out of the receiver. One thing - be careful when pulling up to parking lot curbs. Ground clearance of this hitch is relatively low and I have hit a couple of curbs with it. Thankfully the hitch itself and the mounting points on my Ram 1500 are very strong, and no damage was done other than mangling the rubber hitch receiver cover a bit. Note: I built a wood frame to support the hitch during installation, since I did not have a helper to hold it while installing the attachment bolts.

This front hitch receiver for my 2016 RAM 1500 works great! The installers did not have to cut the facia under the nose of the truck. The hitch fits tight against the facia, but no cutting needed. They did have to drill some holes, but I used professional installers, so I'm not worried. This finally solves my problem of not having anywhere to mount my two bikes while towing my 23' camper. The options for camper bike racks don't work for us for several reasons. Glad I can take my bikes with me on my Saris rack. I purchased an adapter and pin to allow my 1 1/4" bike rack to fit in the 2" receiver. I also purchased the hitch receiver cover separately.

2nd hitch, both fit up great. Left off the roll pan and built our own cover for the sway bar disconnect.

I bought this receiver to add front mounted 'accessories' on my 2007 Jeep Wrangler Unlimited Sahara. I plan on using this to add an extra bicycle rack, a cargo basket, a receiver mounted winch or other 'accessories' needed for my Jeep when I take my family camping. It will also be useful for "front launching" a boat or parking a trailer in tight spots. It took me about an hour to install, although I had already previously removed the lower wind deflector cowling, so did not have to spend time removing it or cutting it for a finished look. Detaching and moving the top trim panel between the grill and the bumper is a must to facilitate the installation. The receiver fits pretty close, although you do have to manipulate it to get the holes to line up with the frame. Follow the instructions and do not tighten any of the bolts until you get it lined up and all the bolts in loosely, then torque it down. As noted in the instruction sheet, the driver's side of the receiver does not sit flush against the frame, there is about a 1/4" to 5/8" gap. The instructions say to use the extra split washers (in the kit) as filler, but they would just rattle around loose in there and provide any benefit, so I omitted them. Once tightened down, the receiver tube was not parallel to the ground, it is slightly higher in the front, sloping towards the rear. It is not off enough to affect my intended use, but may be bothersome to those with type 'A' attention to detail. Overall a good product that will add a lot of flexibility to my Jeep~

We chose the Curt Front Mount Trailer Hitch Receiver so we could safely transport our RAD electric bikes while also pulling our travel trailer. We had it professionally installed onto the front of our Toyota Tundra and it has worked out very well! We are very pleased, and glad that we have it!

Shipping was fast and packaged good with no scratches. I modified my 2010 Tundra skid pan for oil filter changes before mounting. Replaced all 4 OEM tow ring bolts using anti-seize with new longer M12-1.25 X 40MM class 10.9 zinc finished hex cap screws along with new M12 X 24MM OD HARD WASHERS and torqued all 4 to 79 ft/lbs. Mounted new Thule EasyFold XT 2 Hitch Bike Rack and it fits in front without using the hitch extension. All went together as planned and can now take E-Bikes with us while pulling our camper. We are happy campers!