Best Ford Explorer Watersport Carriers

4 on canoe rack only because of supplied lower bracket for cross member attachment.

The product is of good construction but probably due to how it fits on my crossbars it needs additional support. The crossbars for my Honda Pilot are wide blade type and these racks seem more appropriate for narrower square type crossbars. Even with the rack fastened very tightly, the rack can twist back and forth. Last year on a trip across Montana the wind was pretty gusty and it caused the front one to pivot quite a bit and we had to pull off and apply a ratcheting strap over the kayak and under the factory rails to ensure it was held tight and wouldn't move again. This year on the same trip we had bad winds but had a roof rack mounted behind these racks giving it support on the tall side. We had to strap it real good to make sure it didn't move. If we hadn't had that additional support behind it and add'l straps we probably would have had more problems. I think if the top metal bracket had a wider channel to fit our crossbars it would be much more stable. The way it is now it just sandwiches 2 metal plates between my crossbar which allows it to pivot under stress.

Received the the Thule accessories and Yakima Supdog from etrailer.com. It was all nicely packed into one box. As the box said, "the bottom of this box should not be the end of the relationship" I can tell you it won't be! The items were shipped quickly, and they followed up with an email to make sure all was received well. Love the customer service! Also, the Yakima Supdog product is great. Took no time at all to get it on my truck and load up the 2 paddleboards. It was exactly what I was looking to get! Thanks!

The SUPDwag is easy to install and use. Made for Stand Up Paddle boards, but it can work with Surfboards. Wish it was a little bit narrower, hopefully Yakima will make smaller one for the surfing market. I turned my unit around to the driver's side for loading, also protects rain from getting in the lock when driving.

This rack works perfectly for storing a car roof top carrier box. The rack is very sturdy and installed easily on our concrete block wall (utilized concrete screw anchors that were not included).

This rhino rack works extremely well for our Yakima box. It’s off the floor and safely stored! The brackets are very sturdy and the padding provides cushion so the box isn’t damaged. Great product!

Overall I give this Thule Multilift Cargo Lift a five star rating; however installing this device takes some effort and skill. Maybe more effort and skill than the typical DYI'er can provide. The instructions provided do not have any words or dimensions, only pictures. Other than following the routing of the rope through the pullies it didn't provide me any benefit. Also, my system did not come with any screws or bolts. For me that was not a big deal as I have plenty of hardware I can use. There is one center bracket and four pullies to install. The spacing does not line up with typical dimensions so I had to improvise to get the Multilift installed. My garage ceiling has joist spacing that is 16" on center. That is typical, although some may have 24" on center spacing. Either way the spacing for the screws to secure the various components does not match. I guess you could use toggle bolts to hold the components to the ceiling sheetrock but I didn't trust that idea. What I did was to span my ceiling joists with 1"x4" wood and then attach the components to them. The kit comes with a template so getting the actual components set up on the 1"x4" wood strips was simple enough. Once all the components are installed then the rope is routed through the pullies. As you can see in the pictures I had a close clearance between the roof box and my roll-up garage door. I think it is about 2". Since I don't have a tall roll-up garage door I cannot drive my car in or out with the roof box installed. That didn't matter to me since my only goal was to store the roof box out of harms way. My last comment is that it takes two people to lift the roof box up and get the Multilift ropes in place. I tried to do it by myself but that did not work. I do like this Thule Multilift but it took some effort to install it. I really like the way it is raised and lowered by turning a mechanism with a handle. There is a less expensive lift sold on the internet but it did not use as many pullies to raise and lower the roof box and it relied on a rope to lift and lower it.

For our 3 grandkids we needed a way to carry camping stuff. This works great. It opens from either side, key locked on both. We have hung it from the garage ceiling for easy installation. All the stuff fits well.

This is a perfect fit for my needs I found this easy to load by myself. I wasn’t sure about the height of the racks but it turned out to be perfect. I had a full size pickup that was way to tall for this 79 yr old to load, but on the Maverick a with the elevated rack system and the Rhino kayak it works great.

Not the products fault. They were supposed to fit the pre-Thule TracOne rack. Directly asked etrailers support.They don’t fit it. Returned them and grumbled

Arrived quickly and was very easy to assemble and attach to the roof of my Jeep. Now that I have the initial setup complete with the proper placement of the entire system, attaching and removing the kayaks will be a breeze. Will definitely make hauling our kayaks much easier and safer.

This product is excellent. I have transported my kayak on these J Hooks several times going 70+ mph down the highway. It never moves. The bolts that come with it are short. If you have a thick roof rack, you will need longer stainless steel bolts. Make sure you you orient the blue straps with the buckle on top so you can pull down to tighten it up.

Holds Kayaks nice and secure

After putting up with foam blocks for too long I met a fellow sea kayaker who had these. They look great, not bulky and would fit in my TracRac channels. My boats are sea kayaks, 18' long, 22" wide. These saddles adapt great to the hull shapes and are very secure. There is enough slip that pushing the boats up onto them is not a problem. The locking mechanism works, I've never had to reset them (except when I goofed up once and whacked one really hard). Also, the straps are very high quality. The one issue I had was with the pegs in the channels. They were supposed to fit but not quite. A little work with the grinder and all is well. This may not be an issue for newer racks, I don't know. Oh, and no wind singing on the road. In any case I love these things.

Just installed it. So far so good. Ran 2 bike cables side to side with 4 pad locks to secure it for the summer,

Sturdy cradle and easy to install. Difficult to keep tie down strap looped over top of "U" bar while trying to get it over the kayak, keeps slipping down. We made a channel out of foam to keep the strap in place and now it is easy.

These kayak J-style racks worked great, AFTER I went to the hardware store and spent $20 on bolts that actually fit my truck rack. It comes with 2-5/8” mounting bolts that aren’t adequate for a heavy truck rack ( mines a Best.Wyle). I had to buy 4” bolts, lock washers, and nuts). I also wish the locking teeth were mitered instead of square. That would make them less prone to breaking and easier to align.

In the meantime, that boy is not to be in this house ever again These kayak carriers are fantastic! They combine with downloaders to make it possible for my wife and I in our advancing years to get our kayaks on top of our car.

They fit well and I feel my Kayak is safe tied down correctly.

After attempting to mount the individual rack pieces using the “burglar proof” button head screws with the pin in the recess and the short hex wrench with the hollowed out end I discovered that no real burglar would want the rack but would rather have the kayak so the first thing I did after spending 10 minutes trying to insert the hex into the button head screws with the pin inside the recess and attempting to turn the bolts and continually being obstructed by the support pieces and the paint interference on the bolt heads with trying to get the wrench into the recess I knew it was going to be a long frustrating process so I threw them away and purchased new button head stainless steel bolts and a 4mm extended handle hex wrench to turn them. Smartest thing I ever did. You not only have to mount the rack initially but then you have to put the kayak on the roof and remount all pieces again to fit your boat. All kayaks are different to one degree or another. Having to move the individual support and retighten them with the boat on the rack is even more difficult to do than the initial mounting with these “burglar proof” bolts and hex wrench and you will be happy you threw them away before you started the entire process. Try it for yourself at first and then go get the alternate ones. Worth the little investment and stainless steel will not rust away when you want to remove the rack system in the future. Once the rack is on your vehicle and kayak in rack the tie downs supplied are very good quality. Make sure you use the recommended tie down locations and directions, two kayak body ties and ties at front and rear. Due to numerous kayak hull designs it would be nice to have each support pod have a horizontal swivel built into it so it readily conforms to the hull shape. The overall quality of the system should be the last rack you will have to purchase. I only had issues with the supplied bolts and hex wrench. I gave this rack system a three star because of the bolts and hex tool and the individual pods not swiveling and I haven't at this point transported the kayak anywhere so I am waiting to see how it handles long trips with wind loads and constant loading and unloading performances.

I bought this rack to replace a Thule Dock Glide for use on my Malone Microsport kayak/canoe trailer. The Dock Glide worked fine on my rooftop wing bars but wouldn't hold my kayak in position on the trailer. Road vibrations and trailer bouncing would cause the kayak to twist no matter how tight my straps. The Swagman Exo Aero mount is an absolutely perfect fit on the Microsport crossbars with the cutout of the mount top portion and a depression in the bottom bar exactly fitting the cross bar (1 1/4") and is rock solid with no chance of shifting position. The Swagman mount is heavily constructed and the rubber strips on the wide bars hold the kayak like a vise. The boat doesn't shift at all no matter how bumpy the road. Great product.

Hi Carol, I emailed my feed back. Out here in the sticks your website couldnt load properly. It a great product. Perfect for this light duty purpose.

Inno rack pads arrived in a reasonable time and intact/undamaged. They appear to meet all specs and seem well-constructed. Look nice on the rack and will likely work well. My only concerns were: 1) the packaging was riddled with large metal staples . . . over-protected and over-packaged for the product, and a pain to deal with (and not very environmentally friendly). Shipping tape would have been more than adequate. And 2) a very unpleasant odor from the product when opening the package. Took some time to air that out, and had to move the package outside immediately.

I use these consistently without issue.

As all Thule products the Thule universally mounted canoe carrier is great. It came with all required items for safe and easy canoe transportation. There are two straps with pull to fasten for the canoe down, two tie down ropes for each end with nice pull tight and release mechanisms for the cord as well, along with two straps to fasten to the canoe ends used with the pull to tighten cords. The Chevy traverse cross bar had to have the plastic end caps removed for use with Thule canoe carrier. This was because my canoe took up the entire cross bar width to allow for Thule mounts. It is not a big deal to remove the plastic end caps. They only provide a finished stream lined look. Happy and Safe Canoeing

After retiring my 1999 Chevy Silverado 4x4 pickup, I purchased a 2017 Subaru Outback as a replacement vehicle. To transport my 1981 17 foot QT17C Alumacraft canoe on the factory installed roof rack crossbars that came with the Outback, I selected the Thule Portage Canoe Carrier w/ Tie-Downs - Gunwale Brackets - Side Loading - TH819 to do the trick. With one previous transport of the canoe sitting directly on the Outback roof racks, I realized those Outback roof racks were not as durable as the racks on my truck so I sought an improvement to avoid future scuffing and scratching. I did some advance research online and couldn’t be more pleased with this purchase from etrailer.com. I now have a quality product at the right price and these gunwale brackets are a simple solution for this veteran canoe man. The padded brackets grip the canoe and stopped the scratches. The high-quality load straps are nice with the rubber pad that covers the buckle and they easily snug the canoe tight to the racks. I’m also impressed with the bow/stern tie downs that have a very nice ratchet and clip on one end and I secured the supplied hook with a bowline knot to the other end of the ¼ inch rope. The Outback did not have convenient anchor points on the front or back of the vehicle for tie down locations but I found a good solution there as well by ordering the Thule Bow/Stern Tie-Downs - Qty 2 - TH530. This works well with the tie downs I mentioned previously. One limitation to be aware of with the Subaru Outback roof racks and this product is the width of your canoe. My 17-footer measures 34 inches at its widest point at the portage yoke. I had to place the four brackets up tight against the inside roof mounting to achieve the spread and accommodate the canoe placement. The canoe ended up fitting like a glove on the padded brackets. When placing the strap to hold the canoe down to the crossbars, I ran the strap through the vehicles tie down points and then under the crossbars for added security. Total product installation time including securing the canoe can easily be achieved in approximately 20 minutes. I look forward to many more years of safe and happy canoeing. I give etrailer.com an excellent rating for the entire ordering and shipping process on top of the high level of satisfaction with the products I purchased through them. Their customer service and price ensured me that I’ll do more business with them in the future.

On my second attempt to find a carrying rack for a Pelican Mustang 100x recreational/fishing kayak, I took great care seeking out a rack that would provide at least six contact points for the boat. The kicker is trying to get good contact points to securely cradle the shape of the Mustang 100x "twin arched multi chine hull" while also cradling the edge of the deck. Delta kayaks calls a similarly shaped hull a "fusion hull". After doing a ton of google advanced searches for images for a racked up Mustang kayak model, I concluded a J-Style carrier seemed to be a secure solution. The etrailer J-Style - Folding carrier has solved the equation, and for a very reasonable price. Paired with a Sherpa Boat Roller, my 5' 4" wife can load and un-load her Mustang 100x kayak on her own for her afternoon paddles on nearby waterways. Now she needs a cockpit cover to keep out the rain, and her carrying system is complete. And etrailer made it an easy return of the first rack system I tried. Thanks etrailer!

We purchased the carrier for our 2011 Sienna to add to our factory installed roof rack. My 15 year old and I manage using it all the time with no issues. We’ve put both our double and our single kayaks up top with no issues. We leave our rack on all the time and have noticed some sun damage to the foam and plastic, so will it last forever in the TX heat? Probably not, but for the price and ease of use, I’d gladly buy another in a few years. Thank you. I reference the YouTube video whenever I forget exactly how the toe downs go, it’s so helpful. Happy customer.

Very easy to install on roof rack. Just be careful not to lose one of the rubber pieces that help protect your board. They can easily fall off of the rope when tying your board to the rack.

With a little help from youtube, this was one of the easiest things I've ever assembled! LOVE my new SUP rack!!

The keys are an issue (wish they were metal), but everything else is great! I go sunrise kayaking only and hate putting straps on with cold hands at 3:30 in the morning. I have a Nissan Pathfinder and was able to put this on with another set of Malone J-hooks so that I can have a second kayak when I go with someone. Once the fear subsides of it possibly falling off, you realize how quick and easy this thing is to use. It takes me 1 minute instead of 9-18 minutes to get my kayak up and secure. I have tested it at 75mph without any jiggling or issues. I sat on this in my shopping cart forever and finally pulled the trigger. If you kayak at least 10 times a year or are going at high speeds for extended periods of time in warm weather, totally worth it. If not, well, there are cheaper options out there.

Unfortunately I did not have the best of luck with this product . I spoke with the company multiple times to ensure this would work with my rack. It did not. This system is made to work ONLY on a roof rack . I have a truck with a rack and a slot in the middle . We had to make different bolts and holders to install this. For using 2 Paddleboards we also had to modify the back of the racks holders to actually touch the boards to hold them in place . After the modifications and many many adjustments we have it working and it does hold great.

Ordering was very easy and I really like the fact that I had reviews from others "with pictures". That helped me tremendously. The items came within 2 days (WOW). I didn't expect that. They are exactly like show and I will be installing them today. I don't expect any problems. (update after installation) I have now installed and I would have given a rating of Excellent, but I did not because of 1 problem I had. The screws that come with the product are soooo cheap that they all began to strip out as I installed them. And yes I was using the right Phillips head bit and I even had my drill set to stop if it hit resistance. The Phillips head has very small cross threads. If you look at the pics you'll see what I mean. This Phillips head is too small of threads for a larger 2" screw like this. As such, I ended up having to spend $20 on a screw extraction product (Grabit drill extraction) to get 1 of them out. I since replaced all these crappy screws with ones with better heads that are made of actual metal, not paper-mache that looks like metal. By the way, the Grabit screw extraction tool works great... Now that they're up, they look great and do perform exactly like I expected. I would definitely recommend these...

Mounted the kayak rack yesterday and wanted to offer some feedback. In general, a pretty easy process. The screws do seem to be pretty soft; easy to strip a bit, even with 1/8" holes drilled. No disaster, but could be improved. What is wrong is that the straps seem backward. The clamp is mounted so that you must pull up to tighten the strap. Would be better/simpler to pull down on the strap. I see why the longer strap is at the top, but still bad mechanics. I mounted my rack pretty high on the wall, and not being tall, will have a problem using the strap as oriented. In addition, the clamp strap has no means to adjust its length. My kayak (a Poke boat) is pretty slim in cross-section, which makes tightening the strap very difficult unless I get on a ladder. I realize that some of this issue is due to the height that I mounted the rack, but I had to make sure that it put my boat completely out of the way of the car, bikes, etc., with which it shares the space. Would give the rack a good rating, but the odd engineering design and lack of a way to adjust the strap length are disappointing. Overall, does what I need though, just could be a killer rack with some slight changes.

Excellent product! We have two other sets!

I've been using the product for two summers now and it is perfect for what I'm using it for. My canoe is an Old Town Discovery 133, it's very wide and I initially had trouble fitting it in the brackets with how relatively narrow my Rav4 is, but the instructions that came with them mentioned I could just flip them around. That worked perfectly. I only use the brackets and the tie down straps from the kit to tie the boat to the crossbars, and then use the painter lines I put on the bow and stern of the boat to tie those to the car. That rides on the highway very easily with no shifting. With two people, the load/unload time is around 10 minutes as long as one person knows what they are doing. This kit had exactly what I was looking for, seems built to last, and if I ever need another kit to help tie a canoe to a car then I know I can trust this product to get the job done safely and reliably.

Bought a pair of these to go on 59" rhino rack bars on our Outback Wilderness and am really pleased. I left the bars full width - they are not a head banger on the car - and mounted the Hullavators as far outboard as possible which means the kayaks clear the side of the car and wing mirrors without folding them in. I did have to modify one Hullavator to make the Hobie Lynx fit (36" wide Lynx = 36" max Hullavator width)

The Hullivator was for my wife to give her the option of loading and unloading by herself. It couldn’t be better. She now goes kayaking anytime she wants with little effort and no need for me to help her. Excellent product that’s worth every cent. Was super easy to install too.

We needed a better way to haul around 3 kayaks and after looking at a number of options, we settled on the Thule Stacker setup. Installation is simple and the stackers provide a sturdy option for hauling multiple kayaks. One of the best features is that they fold down when you don't need to use them. My shopping experience with etrailer was smooth and shipping was prompt.

My wife uses these to carry two small kayaks in the roof of her Subaru. They work great and we very happy with the purchase. She also likes finding her car easier in the parking lots, even with the carriers folded down.