Best 2017 Jeep Patriot Watersport Carriers

Got my kayak racks today. Easy installation, easy to operate and they look great too! I'd recommend them!

Just installed it. So far so good. Ran 2 bike cables side to side with 4 pad locks to secure it for the summer,

Easy ordering and fast, free shipping. Product was $50 cheaper on etrailer.com than from Rhino Rack themselves. I will absolutely buy from here again.

I purchased the Rhino legs, cross bars and J-style kaya carriers together and could not be more pleased with the combination. The system was installed in an evening and used the next day. Assembly is straight-forward; the racks are easily mounted and removed. I am 6' tall and found it helpful to use a 4' ladder to mount the racks on the cross bars as well as load the kayaks in the carriers.

The Malone Bigfoot Pro Canoe Roof rack is excellent and is super strong. I have two sets of them now, one for a Malone Aero Bars Car Roof Rack, and one for a Rhino Aero Bars Car Roof Rack (both bought at Etrailer). The quality is first rate, so why the 4 stars? The reason is that the support back of the canoe racks is too high. It only needs to be one inch high which matches the rubber pad. Instead it is 3.75 inches high. Every inch higher than necessary makes it harder to lift the canoe over the backs of the canoe racks. If I could cut them easily I would do it, but it looks like it would be too difficult to cut the metal back down to 1 inch. The Canoe racks are even better using the T-Slot Integration Hardware Kit for Aero Styled CrossBars, MPG915. That kit has 5/8" long (functional length) bolts which fit the Malone Aero Bars Car Rack. For the Rhino Rack, it uses a different kit that has 7/8" long bolts. Using the T Slot allows full use of the entire aero bars.

Bigfoot Canoe Rack: etrailer was late sending the order out because their inventory system didn't seem to be working. When they finally found my order, I asked that it be sent to me as a priority shipment. My request was ignored. Otherwise, the order has arrived. I haven't installed it yet, but it's been unpacked and the order seems complete. Also seems pricey for what it is.

It's doing the job of securing my kayak to my rackless prius, at a fraction of the cost. However, the instructions included along with the straps did not work for me. I spent a considerable amount of time adjusting things: the red straps that are supposed to go over the boat and secure on the bars were not long enough. The blue straps are much longer, so I am using the red straps to secure the bars to the car, through the open doors and cinched inside the car. I am using the blue straps to reach over the boat, and I decided to feed those into the car too- feels more secure than to attach them to the bars on top. The black straps for front and back strapping don't work for my car in the way shown, I had to jerry-rig. Overall I have figured out how to make it work, and I'm glad I didn't spend $xxx.xx on a serious rack system.

It's reliable and very easy to install. Trapped several different kayaks onto roof and driven long distance at top speed and no issue with kayak getting loose or moving around.

Would not fit Yakima core bars, so not universal fit.

Easy to put on and remove, fit different diameter roof rack cross beams.

Bought a pair of these to go on 59" rhino rack bars on our Outback Wilderness and am really pleased. I left the bars full width - they are not a head banger on the car - and mounted the Hullavators as far outboard as possible which means the kayaks clear the side of the car and wing mirrors without folding them in. I did have to modify one Hullavator to make the Hobie Lynx fit (36" wide Lynx = 36" max Hullavator width)

The Hullivator was for my wife to give her the option of loading and unloading by herself. It couldn’t be better. She now goes kayaking anytime she wants with little effort and no need for me to help her. Excellent product that’s worth every cent. Was super easy to install too.

The keys are an issue (wish they were metal), but everything else is great! I go sunrise kayaking only and hate putting straps on with cold hands at 3:30 in the morning. I have a Nissan Pathfinder and was able to put this on with another set of Malone J-hooks so that I can have a second kayak when I go with someone. Once the fear subsides of it possibly falling off, you realize how quick and easy this thing is to use. It takes me 1 minute instead of 9-18 minutes to get my kayak up and secure. I have tested it at 75mph without any jiggling or issues. I sat on this in my shopping cart forever and finally pulled the trigger. If you kayak at least 10 times a year or are going at high speeds for extended periods of time in warm weather, totally worth it. If not, well, there are cheaper options out there.

Unfortunately I did not have the best of luck with this product . I spoke with the company multiple times to ensure this would work with my rack. It did not. This system is made to work ONLY on a roof rack . I have a truck with a rack and a slot in the middle . We had to make different bolts and holders to install this. For using 2 Paddleboards we also had to modify the back of the racks holders to actually touch the boards to hold them in place . After the modifications and many many adjustments we have it working and it does hold great.

Good quality materials and easy to install - and uninstall. Two changes would give this product 5 stars: Some type of strap holder at the top of the back rack would make it easier to strap down the kayaks and some type of security lock so someone doesn't borrow your new racks while you are out kayaking. One unique thing to remember for the 2017 Toyota RAV4: the back OEM cross bar is about 3" shorter than the front cross bar - this takes some adjustments for the placement of the racks to fit 2 kayaks and still open the rear hatch.

Used them a couple times and they are performing as expected. I have to mount the kayaks a little forward to clear the 5-er, but they road well at 65 mph into a head wind. Yes, bow straps are used.

They fit well and I feel my Kayak is safe tied down correctly.

After attempting to mount the individual rack pieces using the “burglar proof” button head screws with the pin in the recess and the short hex wrench with the hollowed out end I discovered that no real burglar would want the rack but would rather have the kayak so the first thing I did after spending 10 minutes trying to insert the hex into the button head screws with the pin inside the recess and attempting to turn the bolts and continually being obstructed by the support pieces and the paint interference on the bolt heads with trying to get the wrench into the recess I knew it was going to be a long frustrating process so I threw them away and purchased new button head stainless steel bolts and a 4mm extended handle hex wrench to turn them. Smartest thing I ever did. You not only have to mount the rack initially but then you have to put the kayak on the roof and remount all pieces again to fit your boat. All kayaks are different to one degree or another. Having to move the individual support and retighten them with the boat on the rack is even more difficult to do than the initial mounting with these “burglar proof” bolts and hex wrench and you will be happy you threw them away before you started the entire process. Try it for yourself at first and then go get the alternate ones. Worth the little investment and stainless steel will not rust away when you want to remove the rack system in the future. Once the rack is on your vehicle and kayak in rack the tie downs supplied are very good quality. Make sure you use the recommended tie down locations and directions, two kayak body ties and ties at front and rear. Due to numerous kayak hull designs it would be nice to have each support pod have a horizontal swivel built into it so it readily conforms to the hull shape. The overall quality of the system should be the last rack you will have to purchase. I only had issues with the supplied bolts and hex wrench. I gave this rack system a three star because of the bolts and hex tool and the individual pods not swiveling and I haven't at this point transported the kayak anywhere so I am waiting to see how it handles long trips with wind loads and constant loading and unloading performances.

Very good quality materials for the price point. No tool Assembly and installation is a bonus. I’ve used them for two weeks now, hailing in both two kayak and single kayak configurations. The lever that you pull Up/down on is going to break. Period. If you have the rotating level too tight you can’t switch it up or down and if you have it too loose, it will come unscrewed and then you have a hard time longing up that no internal thread to get it back on. Also, it’s a pain to have to move the entire system to reconfigure needs. Would be nice if it had a slide and lock back in option once on the cross bars. Pulling off 16 wing nuts isn’t ideal. The video was great, appreciated that. Do wish they had shown how to tie down when using two kayaks because once you have one on the system when you place the second on the opposite side, you no longer have access to that center rack. Shipping speed was excellent. The quality of the cam straps is impressive. I have a hand injury and so getting the bolts secured was difficult. The fact that they come with two different lengths to accommodate different rack heights was really nice. Make sure you have your cross bars 24” apart as the instructions say.

This carrier has worked out really well! I paired it with the SportRack Semi-Custom Roof Rack for Naked Roofs - Square Crossbars, and the carrier attached to it perfectly. I drive a 2014 Honda Civic and this carrier has been able to transport two kayaks with no problems. Highly recommend, especially considering the price.

I needed a rear-loading rack because the roof rack on my Ford Ranger is up on the topper, and I needed to fit two kayaks side by side. The roof rack bars are 48" wide and the width of the two boats together is about 52". The center clamps of the Malone Seawing fit between the rack towers nicely. The Malone racks have a grippy ribbed rubber surface which is great to keep the boats in place but makes it hard to slide the boats forward. I throw a towel on them to get the boats loaded and then remove it. My Yakima rack has round bars and the Malone racks tilt on the bar when I load the boats. Easy enough to adjust them after the boats are positioned. In this regard the Malone racks would stay flat with square or aero bars. Strapping the boats down is easy. And as always, eTrailer delivery and customer service is fantastic!

Our kayak club has many members that use this carrier. Since I have back issues, I will use mine on a Malone Eco Light trailer toted from to/from the water using a kayak carrier. Note: Being on a low trailer and so 'accessible', instead of the wingnuts, I bought metric hex nuts to double-nut the bolts to add some security.

Very good advise by Lauren to purchase this product, happy to have bought it. My tandem kayak twin heron fits without problem. It's easy to install and easy to get the kayak up and down

My biggest worry is losing a kayak off the roof, and these carriers are super secure. Never had a worry. They come with ropes, and I always use them, but I've never seen the ropes get any added tension because their so secure. Also, with my bad back, these are pretty easy to load and unload. I'm 6'2 and have no trouble even though these are pretty high up on the Highlander. I always protect the car with a rug, but rarely does the kayak even touch the rug. You don't have to lift the whole weight of the kayak up to shoulder height, just get one end up to the load assist, and then slide it on, same thing in reverse to unload. Easily mount to the factory roof rack, no need for an expensive system. Took them off for the winter, and am getting ready to remount for a new year of exploring lakes and rivers.

These kayak J-style racks worked great, AFTER I went to the hardware store and spent $20 on bolts that actually fit my truck rack. It comes with 2-5/8” mounting bolts that aren’t adequate for a heavy truck rack ( mines a Best.Wyle). I had to buy 4” bolts, lock washers, and nuts). I also wish the locking teeth were mitered instead of square. That would make them less prone to breaking and easier to align.

In the meantime, that boy is not to be in this house ever again These kayak carriers are fantastic! They combine with downloaders to make it possible for my wife and I in our advancing years to get our kayaks on top of our car.

They feel sturdy enough,easy to install om Malone kayak trailer. We'll see how they hold you to Gulf of Mexico salt air.

Super easy to install, quality built, rock solid paring with crossbars. Zero doubt about safety. Could not ask for a better product. Worth every penny. And they fit perfectly with the Malone crossbars for my 2019 Equinox. Customer Service via chat helped me find the one and only pair that would fit those crossbars. So glad I found etrailer.

've previously used the Yakima Kayak Stacker (old style), which worked fine but I always worried the straps would slip off the hook at the top while I was loading boats. They also didn't fold down, so had to be removed after use unless you wanted to look odd and cause a whistle while you drove down the road. They didn't have a universal attachment option, requiring adapters depending on the style and make of your crossbars. More recently I got the Thule "The Stacker", which is a superior solution. You thread the strap through a closed loop at the top, so you don't worry about straps slipping off while you're loading boats. They fold down after use and have a universal style attachment that fits around most styles and makes of crossbars. Good stuff. I really like the straps that come with these, as there is a rubber cover that slips over the metal cam buckle to protect your car's paint while you're tossing the strap over your boats to strap everything in. In order to shuttle our boats for river trips, we needed stackers to fit on both our cars, so it was time for another set. I had never heard of Rhino Rack before, but the lower price than Thile caught my eye, so I read about them and decided to give them a try. The Rhino Rack Nautical Stack used a closed loop at the top, which I liked better than the Yakima or Malone options, and came with the hardware necessary to install them into the C-channel of my Malone aero crossbars, which I wanted to try. I remember that with the Malone stacker, you had to buy the C-channel mount hardware separately. I really like the Rhino Rack Nautical Stack. They are a single post design, unlike the loop style of the Thule "The Stacker". I don't know if this cuts down on vortex drag, but it definitely saves you a couple horizontal inches up where the boats stack. The Rhino Rack Nautical Stack has textured rubber strips on either side of the post, which I believe is intended to cut down on vortex drag, but is also quite helpful in that boats tend to slip much less when you're just leaning them up against the post as you load up before you strap them. That's smart. The Rhino Rack Nautical Stack feels really solid. The mechanism for folding them down and locking them upright is easy to use and feels solid. Installation instructions were good. I tried to install into the C-channels without removing the rubber tubing in my Malone aero crossbars, but couldn't get the little squares to slide into the slots with the rubber tubing in place, so had to cut the tubing, slide the Nautical Stacks into place, then cut down some of the tubing I had removed and replace it in the remaining unfilled crossbar slot. That's not a knock on the Nautical Stack; just a tip in case you're trying to do the same kind of install I did. The one area in which I was less impressed was the tie-down straps that come with this kit. The metal cam buckles have no covering at all, so I'll probably still use my old Yakima and Thule straps instead and use these as backups. But overall, I think these are going to work at least as well, if not better, than the Thule option, and for quite a bit less money.

My wife and I purchased the Rhino Rack Nautic Stack to transport 4 kayaks. We considered similar products by Yakima and Thule, but the acceptable weight limit for the Rhino Rack was there deciding factor. Each of our kayaks weighs 38lbs, and the Rhino Rack was the only item that could handle this load. We were very pleased with etrailer's service and advice. George was extremely helpful. I would highly recommend buying the hood anchors and an extra set of the down straps. The tire down straps are far superior to ratchet-type tie downs that you buy elsewhere - they are strong and SOOO easy to use. I highly recommend the Nautic Stack and etrailer. P.s. we use a bike lock for the Rhino Rack and for our kayaks and they work great for overnight theft protection when we take the kayaks out of town.

Needed a rack to haul my kayaks on my jeep patriot and this price was unbeatable. Works well, though I did not like using the foam blocks. Good first rack for new kayakers.

We needed a carrier solution that folded down easily because of our garage door height. The Malone Pro2 Kayak Carrier has performed flawlessly over the past year. The kayaks remain stable and never shift even at freeway speeds. The foam blocks fit our crossbar well and offered a rattle free ride, which is nice. The one drawback to this system is how difficult it can be to actually route the straps. Without a ladder, it can be nearly impossible to get the strap over the kayak and hooked into the carrier properly. After you find a system that works for you, it becomes easier but I still think that the stationary carriers are more user friendly in that regard.

Timely order processing and quick shipments

My kayak holder works exactly as it should. All parts were included and it was an extremely easy set up. etrailer’s customer service department was on top of everything and extremely helpful in placing my order.

I used the rack to carry my wind surfing board for a ten hour trip to outer banks. Installation went well and easily.Loved design and ease to load and unload as well as to secure rack. One caution though. After riding for about 30 miles I stopped to check cable and had to retighten the cables which had slackened slightly due, I think, to amount of cable on source spool. Had to tighten about two clicks. The board was not in jeopardy of becoming separated from rack.

My representative who helped me was the most helpful representative that I have come in contact with. All representatives are very helpful, but she stood out as she assisted me from start to finish on my order. This is exactly why I use e-trailer for my shopping experiences.

These pads worked well on our Yakima RailBar Crossbars- Item #Y00448-0449 that we also bought from etrailer around 2020/2021. Not sure if etrailer carries the exact Yakima Crossbars anymore, but think they have a similar model. Both the pads and crossbars work well to haul our kayak on our 2019 Subaru Forester. etrailer's customer service rocks! We had a lot of questions purchasing both items and they were great to talk to!

The product came quickly and was so easy to install on my existing roof rails! It is absolutely perfect to fit many needs above and beyond my kayaks and paddle boards. They look so good on my new 2019 Jag F-Pace I might leave them on all the time.