Replacement Breakaway Cable Repair Kit for Dexter DX7.5L A-60 Brake Actuator w Electric Lockout

Question

Question:

I need to replace the brake cable for my DX56FR. I believe it says this is a A-60 actuator and that is stamped into the top of the it.

asked by: Catherine

0

Expert Reply:

Thanks for all the details!

To replace the breakaway cable that came on your Dexter DX7.5L A-60 Brake Actuator w Electric Lockout # DX56FR you just need the Emergency Break Away Cable Repair Kit # DX64XR and you'll be good to go!

expert reply by: Jon G

0

Answer 1

This does happen every now and then, but you will need the Dexter Replacement Emergency Breakaway Cable Kit #DX64XR. This is specifically for the A-60 actuators, which the #DX56FR is. With that said, on the bottom or underneath side of the inner…

view full answer...

Answer 2

When it comes to replacing the Brake Away Cable on The Dexter Brake Actuator #DX29FR The Emergency Break Away Cable Repair Kit for Dexter Axle A-60 Brake Actuators #DX64X is the correct kit for you. . This kit includes the components needed to repair…

view full answer...

Answer 3

We do have the Emergency Break Away Cable Repair Kit #DX64XR for Dexter Axle A-60 Brake Actuators.

view full answer...

Answer 4

The Emergency Break Away Cable Repair Kit #DX64XR is the correct option for a Dexter Axle A-60 brake actuator like the #DX56FR. But, the Emergency Break Away Cable Repair Kit #DX64XR is 17" long with a diameter of 0.1" or 2.64mm.

view full answer...

Answer 5

Yes we do offer just the inner member of the Dexter DX7.5L A-60 Brake Actuator w Electric Lockout #DX56FR with the Replacement Inner Member for Dexter DX7.5L Actuator #DX99FR.

view full answer...

Answer 6

Thanks for the photo! In order to replace the surge brake actuator, I recommend taking a look at the Titan Zinc-Plated Brake Actuator part #T43397007K. This actuator is zinc plated for corrosion resistance, will work with 1-7/8"/ 2" hitch…

view full answer...

Answer 7

The distance between the mounting holes of the Dexter coupler part #DX56FR is 3 inches so it would bolt right up to your trailer. For a manual lockout you could use with this you'd want part #DX94FR. Standard brake line kits like the part #DM5424…

view full answer...

Answer 8

You will need to do some measuring to determine if the 10 Inch Electric Brake Assembly LH, item #AKEBRK-35L, is the correct assembly for your trailer. Measure the diameter of the mounted brake shoe, the width of the lining and the distance between…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 12

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Replacement Breakaway Cable Repair Kit for Dexter DX7.5L A-60 Brake Actuator w Electric Lockout

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching