Replacement Pitch Arm Assembly for a Lippert Edge Awning on a 2022 Forest River Cherokee Alpha

Question

Question:

I am trying to locate a part for a solera awning. Short bar that is used to adjust the pitch with the thumb screw. Part was damaged from water sitting on top of the awning.

asked by: Jeremy C

0

Expert Reply:

The small pitch arm is not offered separately for the Lippert Edge awning you have, so you'd have to replace the entire assembly with the Replacement Drive Arm Assembly for Lippert Edge RV Awnings with LEDs # LC22ED and the Replacement Idler Arm Assembly for Lippert Edge RV Awnings with LEDs # LC62ED.

expert reply by: Bryce D

0

Answer 1

In order to determine the correct replacement for your Lippert Edge awning you'll need to measure the length of your wall mount (see attached photo). Once you've got that number you can look for a replacement based off of that measurement.…

view full answer...

Answer 2

For your 58 inch Lippert Edge RV awning the correct replacement idler arm is the part #LC62ED and the correct replacement drive arm (one with the motor) is the part #LC22ED.

view full answer...

Answer 3

Thank you for providing your part number Steve. I was able to verify you will need the Replacement Idler Arm Assembly #LC75AF. We also have the Replacement Drive Arm Assembly #LC85AF.

view full answer...

Answer 4

We do have the Black version as part #LC62ED.

view full answer...

Answer 5

Since your Solera arm is 58 inches long that would indicate it's a Solera Edge awning which means for a replacement drive arm you would want the part #LC22ED or for a replacement idler arm part #LC62ED.

view full answer...

Answer 6

For your application you need the Pre-Greased Easy Grease Trailer Hub and Drum Assembly #AKHD-655-35-EZ-K. This matches all of the specs you mentioned and while it's only rated for 3.5K axles, it will still work for your Lippert 4.4K axle since…

view full answer...

Answer 7

We do carry the Dometic RV Water Heater #DMC74FR which you could use to replace your Atwood G6A-8E 6 gal RV Water Heater, but I highly recommend switching over to a tankless system like the Furrion RV Tankless Water Heater 60,000 BTU #FR98SR. This…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 12

Hi Jerry, For your 2025 Kia Sorento PHEV you would need the Curt Trailer Hitch Receiver #C37RV for the trailer hitch. The right light kit for your Sorento is going to depend on a few factors. For models with the tow package, like you stated you have,…

view full answer...

Replacement Pitch Arm Assembly for a Lippert Edge Awning on a 2022 Forest River Cherokee Alpha

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching