Replacement Tarp For TruXedo Lo Pro Tonneau Cover 1703866

Question

Question:

Looking for a replacement cover from truxedo part number on the side rail is P/N 1703866 it’s on a 2012 f150 crew cab short box

asked by: Chris

0

Expert Reply:

Thanks for the information. I checked with TruXedo and to replace just the cover on your 2012 Ford F-150's 5-1/2' bed you will need the Replacement Cover for TruXedo Lo Pro Soft, Roll-up Tonneau Cover item # TX5671-CVR.

You will want to put that part number 1703866 where it says Enter a Serial Number or Date Code.

expert reply by: Jerred H

0

Answer 1

I reached out to my contact at TruXedo and she did say that the numbers you found on your tonneau cover refers to the TruXedo Lo Pro QT #TX571101. As you mentioned this particular cover isn't technically a fit for your 2004 GMC Sierra (it fits…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 4

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

Hello Keith, thanks for reaching out. The Brophy Slide In Camper Tie-Downs #HSAB will work for your 2019 Chevy 3500 Duramax Diesel and lance camper. The Brophy tie-downs are more of a universal solution and while they do work, they are not the most…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 12

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Replacement Tarp For TruXedo Lo Pro Tonneau Cover 1703866

Product Page this Question was Asked From

Continue Researching