Troubleshooting Bleeding the Brakes After Installing Demco Surge Brake Actuator
Question:
I am attempting to bleed the brakes on my new Demco actuator surge brake coupler. With the master cylinder full of fluid, I removed the black plastic cover from above the hitch and pumped the plate to push fluid through the new brake line. When we werent seeing fluid coming from bleeder after prolonged pumping, I disconnected the brake line before the Tee. I submerged the brake line in a half full of fluid water bottle. As we continued to pump the surge brake plate, we would only occassionally see an air bubble coming from the line. This continued for dozens and dozens of pumps without the fluid level rising in the bottle. Any suggestions on what we are doing wrong? Thank you
asked by: Dave L
Expert Reply:
It sounds like you may have missed a few steps when attempting to bleed the brakes with your new Demco actuator, like part # DM72VR. I'm attaching a link to the instructions on bleeding the brakes for you to reference.
Let me know if you've followed all of these steps and I can further assist you if you're still having issues.
(click to enlarge)
Product Page this Question was Asked From
Demco Hydraulic Brake Actuator - Drum - Zinc - 2" Ball - 7,000 lbs
- Brake Actuator
- Surge Brake Actuator
- Agricultural
- Construction
- Marine
- Travel Trailer
- Utility Trailer
- Bolt-On
- 7000 lbs GTW
- 2 Inch Ball Coupler
- Drum Brakes
- No Lockout
- Demco
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: Demco Hydraulic Brake Actuator w/ Drop - Drum - Zinc - 2-5/16" Ball - 20,000 lbs
- Shop: Hydrastar Hydraulic Brake Line Kit - Triple Axle - 25' Long, 3/16" Main Line
- Video: Demco Hydraulic Brake Actuator: The Breakdown
- Shop: Demco Surge Brake Actuator - Drum - Zinc - 2-5/16" Ball - 12,500 lbs
- Shop: Demco Surge Brake Actuator w Drop and Electric Lockout - Disc - Zinc - 2-5/16" Ball - 12.5K
- Video: Breaking Down the Hydrastar Hydraulic Brake Line Kit
- Shop: Brake Controller
- Video: Complete Breakdown of the Timbren Axle-Less Trailer Suspension w/ Idler Hubs
- Video: How to Set Up Your Tekonsha Prodigy RF Wireless Brake Controller on a 2006 Land Rover Range Rover
- Video: Breaking Down the Demco Hydraulic Brake Actuator w/ Drop
- Search Results: da16
- Shop: Hydrastar Marine Electric Over Hydraulic Actuator w/ Breakaway and 7-Way RV Harness - 1,600 psi
- Shop: Tekonsha Prodigy RF Wireless Brake Controller - Trailer Mount w Remote - 1 to 3 Axles - Proportional
- Shop: Trailer Axle with Idler Hubs - 5 on 4-1/2 Bolt Pattern - 89" Long - 3,500 lbs
- Video: Let’s Check Out the Manual Reverse Lockout Kit for Demco Hydraulic Trailer Brake Actuators
- Search Results: master cylinder
- Search Results: surge brake kit
- Video: All About the Demco Hydraulic Brake Actuator-DM72VR
- Q&A: Replacement for Atwood 61101 Brake Actuator
- Q&A: How To Determine The Correct Axle Placement For A 16' Tandem Axle Trailer
- Q&A: Why Would Trailer Brakes Stop Working After Replacing Hydraulic Brake Line
- Q&A: Are Replacement Master Cylinders for Titan Model 60 Drum Brake Actuator the Same Size
- Q&A: Replacement Actuator/Coupler to for Trailer with Welded on Drum Brake Actuator
- Search Results: 85841
- Q&A: Mounting Bolt Hole Dimensions for Demco Hydraulic Trailer Brake Actuator # DM72VR
- Q&A: Replacement Bearings for Four Winns Single-Axle Boat Trailer
- Shop: Trailer Hitch
- Search Results: brake controller
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: Trailer Wiring
on Straight Tongue Trailer Coupler
