Parts Needed To Add Electric Brakes To a Shorelandr 3,500LB Single Axle Boat Trailer
Question:
My Yamaha boat trailer came w/o brakes and Id like to add them. From what I can tell, I have a 3,500lb axle. I will need the brake assembly, hubs, and wiring I already have 7pin w/ brake controller in my tow vehicle, but my trailer is only 4 way flat. Can you point me to the parts I will need to complete this job? The following is the information on my Shorelandr trailer: VIN Number: 1MDAPAR13CAXXXXXX Frame: YAV2413SW Model Year: 2012 Finish: BLACK METALLIC Mfg Date: 2012-03-15 00:00:00 Thanks much!
asked by: Scott M
Expert Reply:
For your Shoreland'r boat trailer you will need the following parts.
Self Adjusting Electric Trailer Brake Kit # AKEBRK-35-SA
Galvanized Trailer Hub and Drum Assembly # AKHD-545-35-G-K
Trailer Wiring 7-Way Upgrade Kit w/ Junction Box # HS381-9000
Trailer Breakaway Kit # 20400
It appears your trailer already came with Bearing Buddy Bearing Protectors # BB1980A-SS, be sure to check them for any damage to determine if they should be replaced.
You will need 12 Gauge Wire # 12-1-1 to run to the brakes and I recommend Heat Shrink Butt Connectors # DW05745-5 with any wiring connections since it is a boat trailer.
Products Referenced in This Question
Hopkins Engager Trailer Breakaway Kit w/ Charger, LED Tester, Hardware, and 5 Ah Battery - Top Load
- Trailer Breakaway Kit
- Kit with Charger
- Top Load
- Single-axle
- Tandem-axle
- LED Tester
- Hopkins
more information >
Trailer Hub and Drum Assembly - 3,500-lb Axles - 10" Diameter - 5 on 4-1/2 - Galvanized
- Trailer Hubs and Drums
- Hub with Integrated Drum
- Standard
- L68149 / L44649
- Marine Grade
- For 3500 lbs Axles
- 1/2 Inch Stud
- 5 on 4-1/2 Inch
- 13 Inch Wheel
- 14 Inch Wheel
- 14-1/2 Inch Wheel
- 15 Inch Wheel
- etrailer
more information >
Bearing Buddy Bearing Protectors - Model 1980A-SS w/ Auto Check - Stainless Steel (Pair)
- Trailer Bearings Races Seals Caps
- Caps
- Bearing Protector Grease Cap
- 1.98 Inch
- Bearing Buddy
more information >
Deka Heat Shrink Butt Connector - 12-10 Gauge - Nylon Insulation - Yellow - Qty 5
- Wiring
- Wire Connectors
- Butt Connectors
- 12-10 Gauge
- Deka
more information >
Wiring Kit for Hydrastar Electric Over Hydraulic Actuators
- Accessories and Parts
- Brake Actuator
- Disc Brakes
- Hydraulic Drum Brakes
- Wiring
- Hydrastar
more information >
Product Page this Question was Asked From
etrailer Electric Trailer Brakes - Self-Adjusting - 10" - Left/Right Hand Assemblies - 3.5K
- Trailer Brakes
- Electric Drum Brakes
- Standard Grade
- Self Adjust
- 10 x 2-1/4 Inch Drum
- 3500 lbs Axle
- etrailer
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: Trailer Wiring Junction Box
- Shop: etrailer Electric Trailer Brakes - Self-Adjusting - 10" - Left/Right Hand Assemblies - 3.5K
- Shop: Mounting Hardware for 10" Brake Assemblies
- Shop: etrailer Electric Trailer Brakes - 10" - Left/Right Hand Assemblies - 3,500 lbs
- Shop: Easy Grease Trailer Hub and Drum Assembly for 3.5K Axles - 10" - 5 on 4-1/2 - Pre-Greased
- Shop: etrailer Electric Trailer Brakes - 7" - Left/Right Hand Assemblies - 2,000 lbs
- Video: The Low-Down on the 7-Way Molded Trailer Wire Connector, 4' Long
- Search Results: 7 pin trailer wiring harness
- Shop: Trailer Wiring
- Video: In-Depth Review of the Dexter Hydraulic Trailer Brake Kit
- Video: Complete Breakdown of the Trailer Wiring Junction Box
- Search Results: electric brake wiring kit
- Search Results: electric drum brakes
- Q&A: Adding Electric Brakes To ShoreLandr Boat Trailer
- Q&A: Replacement Hub and Brake Assemblies for 3,500 Pound Trailer Axle
- Video: etrailer Electric Trailer Brakes Review
- Video: etrailer Easy Grease Trailer Hub and Drums Installation - 2020 K-Z Sportsmen Classic Travel Trailer
- Video: Let’s Check Out the Easy Grease Trailer Hub and Drum Assembly for 3.5K Axles
- Shop: Brake Controller
- Shop: Trailer Hub and Drum Assembly - 3,500-lb Axles - 10" Diameter - 5 on 4-1/2 - Galvanized
- Video: A Closer Look at the Brake Mounting Hardware Kit for 7" and 10" Brake Assemblies
- Search Results: 3500 brakes
- Q&A: Torque Spec for 10 Inch Dexter Electric Brake Assembly
- Q&A: Torque Specs For Mounting Brake Assemblies To Brake Mounting Flange
- Q&A: Can Mounting Studs of Electric Trailer Brake Kit # AKEBRK-35-SA be Removed for Longer Studs
- Q&A: Do the Etrailer.com Trailer Brake Kits Include Pre-Installed Mounting Studs
- Q&A: What is the Diameter and Thread Pitch of the Mounting Hardware for 10" Brake Assemblies # BRKH10B?