Coupler Lock Suggestion For A U-Haul 6x12 Cargo Trailer

Question

Question:

Ill be renting a U-Haul 6x12 enclosed trailer, and wanted to know if this Item # e98894 will fit? Thanks.

asked by: John

0

Expert Reply:

I did some research and it looks like your U-Haul trailer will accept 1 7/8"- 2" ball, so # e98893 will be the correct part, although you should double check yourself. If it turns out yours is larger than that, part # e98894 will work accept a 2" to 2 5/16" ball and would be the correct choice.

expert reply by: Bryce D

0

Answer 1

We can definitely help you get exactly what you need to tow a 4 x 8 U-Haul trailer with your 2019 Honda Odyssey and the Curt Hitch #C64NR. According to U-Haul, their coupler height is 18 inches, and when we installed this Curt hitch on a 2019 Odyssey…

view full answer...

Answer 2

The Brophy Hitch Reducer and Extender part #HR26 may work to allow you to travel with the tailgate down however it is enough extension to travel with the tailgate down and tow a trailer without interference. This adapter option also cuts the tongue…

view full answer...

Answer 3

When we installed the etrailer brand #e98862 hitch on a 2011 Honda Odyssey, we found that the receiver height was 14 inches, measured from the ground to the inside top of the receiver tube. The correct ball mount will depend on the coupler height of…

view full answer...

Answer 4

Brophy recommends using two large crescent wrenches to install the #SC23-C. Or at least one crescent wrench on top of the ball and a 1-7/8 inch wrench on the bottom.

view full answer...

Answer 5

To install the Brophy 2-Inch Hitch Ball #SC23-C on Fulton Ball Mount #F47CR you will use a suitable torque wrench (one like #ALL944001) to apply 250-ft-lbs of torque on the nut. I confirmed this with my contact at Brophy Machine Works.

view full answer...

Answer 6

I took some measurements off the etrailer Trailer Coupler Lock #e98895 that will help you to determine if this will fit your coupler. The maximum width of the coupler tongue channel is 4-1/2" wide, and 2-3/4" deep. The locking pin is…

view full answer...

Answer 7

The etrailer Trailer Coupler Lock - Flat Lip 1-7/8" and 2" Ball Couplers - Aluminum - Yellow #e98897 and the etrailer Trailer Coupler Lock for Flat Lip 1-7/8" and 2" Ball Couplers - Aluminum - Silver #e98893 is the exact same…

view full answer...

Answer 8

The etrailer.com Coupler Lock #e98893 fits standard lipped couplers for 1-7/8-inch and 2-inch hitch balls up to a maximum width (including the lip) of 3-3/4-inches. Instead you can use our Coupler Lock #e98895 for 2-inch and 2-5/16-inch balls since…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Coupler Lock Suggestion For A U-Haul 6x12 Cargo Trailer

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching