How to Attach a Cable to a Hand Winch Spool

Question

Question:

How do I attach cable to the drum? Is additional hardware required or is the method of attachment included/built in?

asked by: Timoty

0

Expert Reply:

You can attach the cable to # DL10965 by using two # DL24350 to fasten each cable to the provided holes on the large gear.

expert reply by: Jacob H

0

Answer 1

A worm gear winch like the Dutton-Lainson #DL10952 winch you'd looked at would be ideal. The 1500 lb capacity is more that you'd ever need, but the great thing about a worm gear winch is that it will NOT freewheel if you stop cranking and let…

view full answer...

Answer 2

What you need is a split reel winch like the part #DL10952. This winch will allow you to run a cable in either direction of the spool and will reel both in at the same time. This winch has a capacity of 1,500 lbs which would work well for you even…

view full answer...

Answer 3

For what you are looking to do a split reel winch like the part #DL10965 would be your best option with two of the 1/4 inch metal ropes part #DL24104. This has more than enough capacity and cable length as well.

view full answer...

Answer 4

The winch itself has a 1500 lb capacity, or 750 lbs per cable. If you click the provided link, you can see a helpful FAQ article and a product demonstration video for the #DL10965 winch.

view full answer...

Answer 5

Hey Luke! What kind of trailer do you have? Yes, the Furrion Vision S+ Wireless RV Backup System #FR57AD will fit where the old Vision S was. They use the same mounting bracket and wiring so it should be an easy swap. The only thing that isn't…

view full answer...

Answer 6

Hey Les, thanks for reaching out. So, the 18,000 BTU Furrion Chill Cube AC Unit #LC94DX can replace your Coleman Mach AC unit, but you will need to replace your controller, distribution box and thermostat as well. According to Furrion, the Chill Cube…

view full answer...

Answer 7

Easiest way to tell which gooseneck hitch you have is by looking at the safety cable loops. If they are about as wide as the gooseneck ball hole and are centered with the ball hole it's an EZr, if the safety chain loops are a smaller and offset…

view full answer...

Answer 8

You will actually just need kit #APT6SE-36 which is the same thing only the equalizers in it are 13-1/8 inches long. The hardware with each is specific to the kits so some of the other parts are different but for 2 inch slipper springs and 13-1/8…

view full answer...

Answer 9

Yes, the Fulton High-Performance Brake Winch part #F143100 will work with the Universal Hand Winch Right Angle Mounting Bracket part #DL24110. I went out to our warehouse and test fit the two products together to confirm this for you. I have attached…

view full answer...

Answer 10

The Hex Shaft for Dutton-Lainson Worm Gear Winches #DL406102 that you referenced is designed to fit Dutton-Lainson worm gear winches so yes, it will work on the Worm Gear Hand Winch #DL11002 that you referenced. However, this product is designed to…

view full answer...

Answer 11

The Dutton-Lainson Hand Winch #DL10976 will have the split reel and it is also rated for 2,000lbs while the Dutton-Lainson Hand Winch #DL10954 is only rated for 1,500lbs. The split reel design will allows for simultaneous operation of two lines from…

view full answer...

How to Attach a Cable to a Hand Winch Spool

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching