Comparing Buddy Bearings and EZ-Lube Grease Caps

Question

Question:

I noticed that when looking at ez lube caps bearing buddy caps come up as premium parts and wondering why? They push grease in opposite directions. ?????

asked by: Justin C

0

Expert Reply:

The Bearing Buddy Bearing Protectors like part # BB1781 will only work for standard spindles, not those with grease fittings in the end which are also known as EZ-Lube. They both are designed to provide easy lubrication to the bearings without having to pull apart the hub. If you have EZ-Lube hubs you'll have to use grease caps, preferably ones that have an easy to remove center section like the Grease Caps part # RG04-040.

expert reply by: Conner L

0

Answer 1

The great thing about Bearing Buddy like part #BB1781 is that when you add grease to your system with the included fitting, it will move the spring-loaded piston outward and allow grease to seep around the edges to keep from damaging the seal. You…

view full answer...

Answer 2

It is possible to over-fill a hub that has a Bearing Buddy bearing protector such as #BB1781. The convenience of easy filling through the zerk fitting can often mean we can be tempted to keep adding more grease. ("If a little is good, then more…

view full answer...

Answer 3

The portion you need to measure is not the cap, but the the hub bore. Remove the grease caps and measure the diameter of the opening the caps occupy. This is the hub bore. You will need an accurate measuring devices like a set of dial calipers that…

view full answer...

Answer 4

Check the existing wheel bearings for the reference numbers as shown in the provided photo. If the bearings are damaged and the number can't be read, try pulling the other wheel on the axle and looking there. If you can't make out any of the…

view full answer...

Answer 5

In order to pick out the correct bearing buddy you will need know the pilot hole of your hub. To do this, remove the wheel and tire and remove the grease cap from the center of the hub. Usually it is a metal cap that is just lightly hammered into…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 8

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 9

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 10

The BTR and BT8 denotations refer to the spindle, not the trailer hub. The difference between a BTR and BT8 spindle is that the BTR spindle uses a 1.063" diameter L44649 bearing and the BT8 spindle uses a 0.99" diameter L44643 bearing. In…

view full answer...

Answer 11

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 12

Hey James, you can go with a 4k axle leaf spring like the part #e22YR in place of what you have now while it has a slightly higher weight capacity it's not enough that it would create a harsh ride quality. This is a 26 inch long spring though so…

view full answer...

Comparing Buddy Bearings and EZ-Lube Grease Caps

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching