Troubleshooting Error Retract Timeout on LCI RV Levelers

Question

Question:

My Lci has a error as soon as I turn on the key it says , Error retract time out ,then goes to a screen that says retract leveler for service . And the controls seem to be locked I cannot do nothing with it.

asked by: Dwayne V

0

Expert Reply:

If the touch pad is showing "Retract Time out Return Levelers for service" all you need to do is hit, enter and retract at the same time. That will clear that code. I confirmed this with our contacts at Lippert.

Let me know if that fixes the issue or if the error code returns.

expert reply by: Jameson C

0

click to enlarge

Answer 1

Hey Will! You can flat tow your 2014 Jeep Wrangler Willys with a Dana 44 axle as long as you have a two-speed transfer case. Make sure to check your owner's manual to verify this information. Does it have the standard bumper on the front?…

view full answer...

Answer 2

If the touch pad is showing "Retract Time out Return Levelers for service" all you need to do is hit, enter and retract at the same time. That will clear that code. I confirmed this with our contacts at Lippert.

view full answer...

Answer 3

There may be a bunch of different reason why your Lippert Level-Up system has suddenly stopped working. The most common reasons are due to a dead battery, extending your jacks too far, or a blown fuse. The first thing you should check for is the easy…

view full answer...

Answer 4

I just spoke with my rep at MORryde and she said that you are able to use the CRE3000 MORryde Rubber Equalizers for Tandem Axle Trailers - 33" Wheelbase - 8K item #MR87ZR on a tandam axle trailer with 31 inch spacing if your are using 24 inch…

view full answer...

Answer 5

The Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System w Touchpad and Remote - 4-Point Set #LC358590 has 4 35-amp fuses located on the controller. Attched is a complete wiring diagram for you to check out.

view full answer...

Answer 6

We have heard of this issue before on the Lippert Ground Control systems #LC358590. Here is the recommended procedure for clearing the error code: Extend all jacks at least 6 inches. Then press and hold the RETRACT button until the jacks begin…

view full answer...

Answer 7

I reached out to my contact at Lippert and they said that it sounds like you just aren't holding the 4 buttons for the reset long enough. It requires 5 seconds, but many people will count to 5 a little too fast and the system won't reset. He…

view full answer...

Answer 8

You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better option…

view full answer...

Answer 9

If you've already tried resetting and cleaning the unit then you'll need to replace it. I recommend the Furrion RV Stereo - Single DIN - HDMI, AUX/USB, Bluetooth, NFC, App Control - 60W - 2 Zone - 12V Item #DV3300SBL to replace it. This…

view full answer...

Answer 10

It sounds like you just need to figure out which wires are supposed to go where for the installation of the Kwikee Step Motor Conversion/Upgrade Kit #LC379145 on your 1997 Georgie Boy. I am attaching a wiring diagram for the control module for you to…

view full answer...

Answer 11

The Replacement Control Module for Lippert Electric Coach Step #LC301702 has the purple wire that connects to the door light switch. The other end of the switch #LC301694 connects to the Replacement Wiring Harness for Lippert Electric Coach Step…

view full answer...

Answer 12

I attached the wiring diagram you referenced for the Lippert Power Steps Module #LC301702. The second green wire would get grounded to the chassis of the step. The extra wire you mentioned would just need to be capped off and not used like you said.…

view full answer...

Troubleshooting Error Retract Timeout on LCI RV Levelers

Product Page this Question was Asked From

Continue Researching