Bearing Replacements for Trailer with L44610 L44619 L68111 L68149 442251

Question

Question:

Looking for wheel bearings 09067 with race 09195 do these cross to your numbers?. FYI - This hub uses a 15245 race and 15123 bearing maybe a kit available. Also looking for wheel seal 7038SA National for this hub. The other axle on this trailer uses L44610 race L44619 brg L68111 Race L68149 brg 442251 Seal Is there a kit for theses? Thank you

asked by: Bill B

0

Expert Reply:

The first set of bearings are Timken which we don't carry and don't have a cross reference for.

We do have the race # L44610, with what I believe you meant to type # L44649, race # L68111, and bearing # L68149 with seal # RG06-050.

expert reply by: Jameson C

0

Answer 1

Based on my research the Redline Grease Seal #29031 that you ordered is the correct seal for your 22834 hub (which is what I assume you have based on the #2788 inner bearing and #1779 outer bearing that you also purchased). We do not have a ring…

view full answer...

Answer 2

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 3

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Hey Barry, sure do! The seal that comes with the #DX87UR bearing kit is a 1.719" ID and 2.565" OD. We offer this seal individually as part #58846.

view full answer...

Answer 6

You are going to want either our Bearing Kit #BK2-100 or the Timken Kit #TMK52VR. Both of these kits will give you the inner/outer bearings and races along with a grease seal and cotter pin/D-washer for one hub. You always want to replace the race…

view full answer...

Answer 7

Hey Eric, so we do have what you need with the replacement cap part #VA55JR but the one you mentioned is smaller so it would not work for you. The cap you need is 4 inch diameter and the one you referenced is 3.75 inch.

view full answer...

Answer 8

After you've packed the bearings and assembled everything, carefully slide the hub assembly onto the spindle and install the outer bearing. Install the spindle and tang washer and run the spindle nut down finger tight, then rotate the hub back…

view full answer...

Answer 9

In order to verify the spindle dimensions so that you can pick out the correct hub/drum you have to get exact dimensions. For that you need to use a digital caliper like part #PTW80157. For how old your trailer is this is especially important as the…

view full answer...

Answer 10

You can verify that the 10-19 grease seal included in Bearing Kit #BK2-100 is the correct one for your spindles by taking two measurements. First you want to measure the rear hub bore where the seal is inserted. The seal's outer diameter needs to…

view full answer...

Answer 11

We recommended to repack the wheel bearings on your trailer every 12 months or 12,000 miles. There is not a specific guideline as far as actually replacing the bearings. When repacking them with grease, you will also just want to check for any damage…

view full answer...

Answer 12

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Bearing Replacements for Trailer with L44610 L44619 L68111 L68149 442251

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching