Fulton F2 Jack Mounted on a Ranger RT188 Trailer

Question

Question:

Thought I would send you another customer photo of what the Fulton F2 Jack looks like mounted up on the trailer. FYI, the dual wheel model will contact the frame on this particular Ranger Trail trailer, but the single wheel seems to do fine.

asked by: Kenneth E

1

Helpful Expert Reply:

Thanks! I attached the picture you submitted so that other customer can see what the Fulton F2 part # F1413140334 looks like installed on Ranger RT188 trailer.

expert reply by: Jameson C

1

click to enlarge

Answer 1

The Fulton Bolt-Thru Swivel Marine Jack, Weld-On #FXP15W is designed to mount to its mounting bracket with a single center bolt. The mounting bracket designed to work with this jack is part #P9012-00. In order to replace the weld-on jack on your boat…

view full answer...

Answer 2

The Fulton Jacks that have the 3"x5.5" bolt pattern are typically the center bolt thru style. For a replacement the Fulton Bolt-Thru Swivel Marine Jack part #F1411300301 is an excellent choice. It will replace the jack only portion of your…

view full answer...

Answer 3

The Fulton Bolt-Thru Swivel Marine Jack - Weld On - Sidewind - 10" Lift - 1,500 lbs, #FXP15W will work for your application. A similar jack like the Fulton XLT Bolt-Thru Swivel Trailer Jack - Weld On - Sidewind - 12" Lift - 1,500 lbs,…

view full answer...

Answer 4

I can't see any part numbers or manufacturer names from your picture, but the Fulton XLT #F141132 does look very similar. I went out to the warehouse and measured the bracket that the bolt, washer, and nut go through for the installation. The…

view full answer...

Answer 5

The correct replacement for the Fulton Magnum Series Trailer Jack on your trailer is the Fulton Bolt-Thru Swivel Marine Jack part #FXP10W0301 if you have a bolt-thru mounting bracket or part #FTJ120W0301 if you have a snap-ring mounting bracket. I…

view full answer...

Answer 6

The only trailer jack that will work with your existing mounting bracket and not contact the boat with a full rotation of the handle is the Fulton Bolt-Thru Swivel Marine Jack part #F1411300301. I understand this does not have the sharkskin coating…

view full answer...

Answer 7

You can install the Fulton F2 Jack, #F1413040134, on your trailer, but you will need to pick up smaller u-bolts. The u-bolts included with this jack fit 3 inch x 3 inch and 3 inch x 4 inch frames. You could pick up two of the CE Smith U-Bolts,…

view full answer...

Answer 8

The Fulton F2 Swing-Up Trailer Jack #F1413040134 (as well as other F2 jacks) has that plastic piece that as you referenced is #9 in the exploded diagram. I reached out to my tech contact at Fulton and unfortunately that is not a replaceable part. You…

view full answer...

Answer 9

Hey Mike, thanks for reaching out! I just pulled the Fulton XLT Boat Trailer Jack w/ Wheel #F26ZR from our warehouse and doubled checked the lift. It is a 10" lift so I'm wondering if Fulton is trying to count some of the adjustments in the…

view full answer...

Answer 10

The Curt #C13363 Class III receiver hitch you'd looked at is indeed a fit for your 2019 Jeep Compass. The short and direct answer: I've looked over the 'Trailer Towing' section of your owner's manual, and found no blanket…

view full answer...

Answer 11

I have a few options that may work for you, however, we are not aware of any stainless steel jacks on the market since the discontiuned SeaSense jack. Since you are using this jack with your boat, I recommend looking at the Fulton F2 Swing-Up,…

view full answer...

Answer 12

It is possible to install CE Smith Bunkboard Guide-On Kit #CE27600K75 in the way you have suggested. But it may require trimming parts of the tubes should they interfere with the boat. The only part of the set up you would want to make contact with…

view full answer...

Fulton F2 Jack Mounted on a Ranger RT188 Trailer

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching