Installation of Extang Trifecta 2.0 Tonneau Cover on 2019 Honda Ridgeline

Question

Question:

I have a 2019 Honda Ridgeline. I am interested in the extang trifecta 2.0 for a tonneau cover. Just want to make sure this one will fit my truck. Also, how is it installed? Is it pretty easy?

asked by: Rex A

0

Expert Reply:

I am happy to confirm for you that yes, the Extang Trifecta 2.0 Soft Tonneau Cover # EX92590 is confirmed to fit your 2019 Honda Ridgeline; I checked with the manufacturer to make sure.

The installation of this tonneau cover is pretty easy. Not only is there no drilling needed to install this cover on your '19 Ridgeline, there are no tools needed at all! The Trifecta 2.0 uses a clamp system - as you can see by the cut out of the instructions I added - to secure the cover to your Ridgeline's bed rails. It will even work if you have a plastic bed liner which covers access to the bed rail flange. You will only need to cut away a section of the liner so the clamps can contact the bed rail flange.

I have added a link to a video review of the Extang Trifecta 2.0 Soft Tonneau Cover # EX92590 for you to check out as well.

expert reply by: Kyle S

0

click to enlarge

Answer 1

Hi Dan, So the easiest thing to do is actually remove that 4-way on your 2019 Honda Ridgeline and replace it with the T-Connector Vehicle Wiring Harness with 7-Way Trailer Connector #118288. This will plug into that same gray connector the 4-way did,…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

Hey Jeff, the Extang Trifecta 2.0 part #EX94590 that you referenced comes with everything needed to install on your '24 Ridgeline. You wouldn't need to provide any additional hardware.

view full answer...

Answer 4

I do have an option for you but the TruXedo Pro X15 Soft Tonneau Cover part #TX1430601 will only allow you to open the in-bed trunk about 80% of the way because the rails sit inside the bed around an 1" or so on each side. If you want to be able…

view full answer...

Answer 5

I went through each of the available tonneau covers for your 2018 Honda Ridgeline and the only types available - either soft or hard covers - may require you to cut into your bed liner, but only if it covers the metal flange on the sides. I recommend…

view full answer...

Answer 6

The Extang Trifecta Signature 2.0 Soft Tonneau Cover #EX94590 you referenced for your 2022 Honda Ridgeline most certainly does come with mounting hardware and does not need to be cut to install. The tracks that come with this cover will bolt onto the…

view full answer...

Answer 7

Hey Pamela, thanks for reaching out! The Extang Trifecta ALX #EX98CV that fits your 2017 Honda Ridgeline is the same as the Trifecta 2.0 #EX92590 but with a slight upgrade to using the rotary release latching system and an automatic latch that makes…

view full answer...

Answer 8

If the bed liner on your 2019 Honda Ridgeline covers the side rails then you will need to do a little but of trimming for the Extang Trifecta 2.0 #EX92590 to fit properly. I have included a picture from the installation instructions for you to…

view full answer...

Answer 9

I have a tonneau cover solution for your 2019 Honda Ridgeline that is going to allow you to fully open your truck but it's not the Truxedo Sentry either as the rails would interfere. Instead you'd want the Extang Trifecta 2.0 part #EX92590…

view full answer...

Installation of Extang Trifecta 2.0 Tonneau Cover on 2019 Honda Ridgeline

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching