Troubleshooting Error Message on Panel for Lippert Ground Control Leveling System

Question

Question:

the lci control panel wont come on unless i unplug it and when it comes on it reads ****error**** press enter to acknowage i press enter nothing happen. cannot turn it off unless i disconnect the battery and unplug the power cord all it does it makes a beeping sound

asked by: William P

0

Expert Reply:

I spoke with my contact at Lippert regarding the error message issue you are having with your Ground Control Leveling System. He says it sounds like the controller may have gone bad. To check this you can cut power to the controller and just do a hard reset for about 15 minutes and then power the unit back on. If you still get the error message on the panel then the controller will need to be replaced.

If you have the 3.0 Ground Control Leveling System # LC358590 the correct replacement controller is part # LC304136.

expert reply by: Chris R

0

Maria I.

5/23/2020

Hall Power Short error, unable to clear. Appeared when 5th Wheel was hitched on to truck. RV is unusable

Reply

Chris R.

5/25/2020

If you're able to operate the jacks, extend all of them at least 6". Then press and hold the retract button until the jacks begin going down. Once they're all fully retracted the error code should clear. Just let me know if the error persists for some reason.

Reply

María I.

5/25/2020

@ChrisR thanks! No nothing works. I turn on the system by pushing the up /down arrows and immediately starts blinking red. If I go inside I only see the message Hall Power Short click enter. I do it and it comes up again.

Reply

Chris R.

5/28/2020

@MariaI Thanks for the info. I'm sorry this is causing so much trouble. It sounds a bit like there may be a short on the actual wiring for the system. Inspect the power wire going to the battery and check for any exposed or pinched sections that need to be replaced. Make sure both the power and ground wires are still securely connected. Lastly make sure the battery itself is still in good condition and fully charged.

Reply

See All (4) Replies to Maria I. ∨

Answer 1

There may be a bunch of different reason why your Lippert Level-Up system has suddenly stopped working. The most common reasons are due to a dead battery, extending your jacks too far, or a blown fuse. The first thing you should check for is the easy…

view full answer...

Answer 2

The 6-Amp Auto Reset Breaker for Lippert Power Stabilizer Jack #LC134181 is self-resetting. It automatically will reset itself after the breaker trips. If the circuit continues to draw more amperage than the breaker is rated for it will constantly…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 7

It sounds like you may already have a 4 way connector on your vehicle, which is half of the battle. In order to operate the Curt Echo Mobile Wireless Brake Controller #C51180 you will need an almost fully functional 7 way connector; using something…

view full answer...

Answer 8

Hey Mike, thanks for reaching out! The 16K Pullrite SuperGlide #PUL43RR is an excellent option for towing your Grand Design with your 2025 F-250, and if you lockout your Lippert Turning Point pin box you'll be able to use them together. You…

view full answer...

Answer 9

We can definitely help install a brake controller and 7-way on your 2024 Toyota Grand Highlander but first the brake controller I recommend is the Redarc Tow Pro Liberty part #RED24FR with the install harness part #RED69FR. As this controller puts…

view full answer...

Answer 10

The best option for wireless brake controllers is the Curt Echo #C51180. It is the easiest to plug in and go when you need to use a brake controller with your trailer. Once you have a 7-way connector installed in your vehicle, all you need is to…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

Hey Travis, we have the Air Lift LoadLifter 5000 kit part #AL47PD that is a confirmed fit for your 2021 Ford F-150 and also is compatible with in-bed hitches like your B and W Turnoverball Gooseneck part #BW77FR. What are you towing?

view full answer...

Troubleshooting Error Message on Panel for Lippert Ground Control Leveling System

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching