Locating Replacement Landing Gear Follow Leg for Keystone Raptor
Question:
Good morning. I have a 2006 Keystone Raptor Mod# RP3612 TS. Triple slide with the Lippert Landing Gear. The slave leg ie. Driver side leg has snapped at the top piece where the horizontal cross bar mounts. It is up over the top of my generator so I cant tell exactly what part I need. It did not shear the bolt, looks like its part of the leg itself.
asked by: Bill
Expert Reply:
If the damage looks to be part of the follow leg itself, then your best bet is to replace the entire leg. We have a large selection of replacement follow legs available, which I have attached below. I recommend searching for a model number somewhere on your landing gear system to make sure you get the correct replacement leg. You can also take a measurement of the distance between the bracket stops on the current leg along with its overall length.
For example the Lippert Landing Gear Follow Leg # LC179014 has a distance between the bracket stops of 17-1/2 inches from outside to outside and a measurement of 15-1/2 inches from inside to inside on the brackets. The outer tube height is 29-1/2 inches. I have attached an image with these dimensions labeled for clarification.
Products Referenced in This Question
Replacement 5th Wheel RV Landing Gear Follow Leg w/ Snap Pin for RVs
- Accessories and Parts
- Camper Jacks
- Trailer Jack
- Legs
- Follow Leg
- Lippert
more information >
Product Page this Question was Asked From
Lippert Venture Follow Leg Repair Kit for 5th Wheel RV Landing Gear
- Accessories and Parts
- Camper Jacks
- Trailer Jack
- Hardware
- Repair Kit
- Lippert
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: Replacement 5th Wheel RV Landing Gear Follow Leg w/ Snap Pin for RVs
- Shop: Landing Gear Set - 36-1/2" Lift - 8,000 lbs
- Video: All You Need to Know About the Landing Gear Set
- Shop: Landing Gear Set w/ Handle - 36-1/2" Lift - 8,000 lbs
- Shop: Replacement Heavy-Duty Landing Gear Jack Leg for Ground Control 2.0 - Extended
- Shop: Lippert Components Tuson High Speed 5th Wheel RV Landing Gear Motor
- Shop: Lippert HD 6500-lbTuson 5th Wheel RV Landing Gear Motor
- Shop: Lippert Venture 5th Wheel RV Landing Gear Motor
- Q&A: Difference Between Stromberg Carlson # LG-196308 and Lippert # LC196308 Replacement Motors
- Q&A: Replacement 5th Wheel Landing Gear Motor for Venture 9000
- Q&A: Heavy Duty Replacement Landing Gear Motor For Venture M-9000-PK
- Video: An In-Depth Look at the Lippert Venture Follow Leg Repair Kit for 5th Wheel RV Landing Gear
- Q&A: Landing Gear Skips and Legs Wont Extend When Raising Trailer Jack
- Q&A: Replacement Gearbox and Repair Kit for Venture Landing Gear
- Q&A: Troubleshooting Landing Gear Not Lifting 5th Wheel
- Q&A: Does the 5K etrailer Electric A-Frame Trailer Jack Come with a Warranty
- Search Results: landing gear
- Article: 30-Amp and 50-Amp RV Service: What's the Difference?
- Video: In-Depth Review of the Landing Gear Set
- Article: Trailer Wiring Diagrams
- Shop: Trailer Hitch
- Search Results: trailer jack
- Search Results: rv vents and fans
- Article: How to Measure for Travel Trailer and Fifth Wheel Steps
- Video: In-Depth Review of the Ventline Ventadome Trailer Roof Vent
- Search Results: camper jacks
- Video: Replacement Dome Assembly for Ventline Ventadome Trailer Roof Vent Spec Review
- Article: How to Replace an RV Roof Vent Cover
- Shop: Trailer Wiring
- Search Results: lc142178
on Accessories and Parts
