Replacement Roof Vent Cover for 2000 Skamper Sport 23D Pop-Up Camper Trailer

Question

Question:

Hello, Need a vent lid. Here is a photo. Thanks.

asked by: Jim

0

Expert Reply:

Thank you for the photo of your trailer roof vent for which you need a new lid.

I conferred with several of my associates regarding the photo of your trailer roof vent which requires a replacement lid. Interestingly, this hinge design seems about halfway between a 3-point type like # 69284 and a continuous type like # BV0554-01.

After much back and forth we came to the determination that you need a 3-point. We have only one 3-point-hinge type lid # CAM40153.

But we do have a universal-fit lid kit, part # MA00-335001, that includes its own hinge mechanism and which fits vents from Elixir, Ventline, Jensen, Hengs, and others. If you can find one of those brand names on your vent that's a good sign!

In all honesty, given that the cost of a whole new vent is not that much more than this universal lid kit, you might consider replacing the entire vent with a more modern one for which parts should tend to be more readily available well into the future. I linked you to our manual vent product assortment.

Since you have what appears to be a coated metal roof the installation kit you'll want to use is part # 344270KITW which includes hardware and sealant.

expert reply by: Adam R

0

click to enlarge

Answer 1

When choosing the slider you want to measure the outside front of box width including the flange. Then you need to select a slider that extends a minimum of 2-1/2 inches beyond each side of the box width. For example, the Black Solera Slider…

view full answer...

Answer 2

Hey Jason, thanks for getting in touch. For a Dometic AC unit I recommend the SoftStartRV Soft Start for Single Zone Air Conditioner Setup #SSR54FR. This is a universal soft start, and it is known to work with the Dometic units. The chart below shows…

view full answer...

Answer 3

To power the Solera Smart Arm 12V Power RV Awning #LC517486 you simply will connect your white power wire with the white wire from the switch and run that to the positive terminal of the battery inline with the supplied 15amp fuse. From here, connect…

view full answer...

Answer 4

I called and spoke to the technician at Lippert about the gear packs. If the arms that attach to your slide out are 2 x 2 you will need Gear Pack part #LC281331. If the arms that attach to the slide out at 2.5 x 2.5 you can certainly use Gear Pack…

view full answer...

Answer 5

Hey Ron, good to hear from you! How long are your current U-Bolts? The U-Bolt Kit #APUBR-8 could potentially work as it has 7" long U-Bolts, but it really boils down to what you currently have. For something longer we have the MORryde U-Bolt Kit…

view full answer...

Answer 6

Hey James, you can go with a 4k axle leaf spring like the part #e22YR in place of what you have now while it has a slightly higher weight capacity it's not enough that it would create a harsh ride quality. This is a 26 inch long spring though so…

view full answer...

Answer 7

All of our trailer spindles are shown on the linked page, but none of these has a stub end to fit 2 x 3-inch tubing. All are either round like #TRU74FR or square like #TRU47FR. For a fabrication project like yours a better solution may be a bolt-on…

view full answer...

Answer 8

Hey Mitch, yes that is something that we do! You will have to call in to our customer service department to get everything ironed out though. Do you already have your setup or are you also needing that as well? If you don't you're going to…

view full answer...

Replacement Roof Vent Cover for 2000 Skamper Sport 23D Pop-Up Camper Trailer

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching