Adding Reverse Lights To Semi Trailer 48 Foot Flatbed Through Connecting to 7-Way

Question

Question:

If I wanted to install reverse lights on my semitrailer 48’flatbed what connection to I come off of on the 7 way?

asked by: James

0

Expert Reply:

If you use the 7-way that is used for commercial/industrial/agricultural application like # PK11720 or the RV/standard 7-way like # HM47210 you will need to utilize the same location. The reverse signal should be connected to the center location of either application.

You will simply need to make sure your wiring corresponds with the function locations. I've attached a photo to assist. For a 7-pin that normally does not have a reverse light, that means utilizing the auxiliary in the middle for that function.

expert reply by: Jason S

0

click to enlarge

Mike

2/20/2025

if I use the center pin for back up lights will I lose the abs for the trailer?

Reply

Jon G.

2/20/2025

@Mike Yes, if you have the commercial/agricultural 7-Way pin system and you remove the connection for the Aux/ABS power and replace it with back up lights then you will lose the ABS feature if you currently have it.

Reply

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

Hello Tim, Are you asking if you can back up with just the head installed on the Weigh Safe True Tow Weight Distribution Hitch #WS79VR, when you put the trailer coupler onto the ball? If so, then yes because at that point it is really just a ball…

view full answer...

Answer 4

Hello Brandon, Congrats on the new camper! When picking out the right weight distribution hitch it is most important to be as close to the tongue weight as possible. You said that your tongue weight is around 700 pounds, I am not sure if you are…

view full answer...

Answer 5

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 6

On a 7 pin round which is the common connection on a semi trailer, the clearance/marker lights are at the 10 o clock position when you look at the trailer wiring connection. When looking at the connector on the back of the truck, that will put the…

view full answer...

Answer 7

Hey Willyd, it looks like you have a 7-way round connector which is a bit more rare and for that we only have a 7-way to 4-way adapter like the part #47405. Does your trailer with a 5-way actually use the 5th circuit? If so what is it for?

view full answer...

Answer 8

Either way is correct. It depends on if you want to keep the semi-style 7-Way (if you need to tow that type of trailer) or if you will never be towing a semi-trailer. If you need to keep the 7-Way semi active on the truck, then you would need to make…

view full answer...

Answer 9

Hey Bob, great question. It was about 7 degrees here in Missouri this morning, so I can relate to the cold. I do have a good solution for this too. What I would do is replace your current 7-way cord with the Curt Cold Weather 7-Way RV Style Connector…

view full answer...

Adding Reverse Lights To Semi Trailer 48 Foot Flatbed Through Connecting to 7-Way

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching