Common Torque Specifications for Lug Nut Size

Question

Question:

What is the torque for a UTG Rims with 9/16 stud

asked by: Roch B

0

Expert Reply:

The torque for the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles - 12" - 5 Spoke Utility # 8-174-5UC3 is not specified by the manufacturer. For 9/16 inch studs, the typical lug nut torque will be 120-140 ft lbs based on most of our manufacturers. I've attached a photo of typical torque values to assist.

expert reply by: Jason S

0

click to enlarge

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

The recommended lug nut torque for your 7,000lb axle depends on a few factors like wheel size, stud size etc. Check out the attached photo which shows the torque specs for a variety of applications. I see you were looking at the Dexter Nev-R-Adjust…

view full answer...

Answer 3

Torque specs for wheel lug nuts will vary depending on the diameter of the lugs, type of lug nut and the wheel's material. The linked chart details the recommended torque for many combinations. Dexter Hub/Drum #84546UC3 has 1/2-inch studs and…

view full answer...

Answer 4

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 5

I spoke to Dexter and they said there is a bit of a process for installing the spindle nut properly. 1. You will need to thread on the inner nut, rotate the hub, then tighten the nut to 100 foot pounds. 2. Loosen the nut to remove the torque, making…

view full answer...

Answer 6

Hi Doug; it looks like previous customers have said their Dometic A&E 8500 was a 21' awning. I recommend measuring from the center of the left arm to the center of the right arm to verify this. Assuming that is correct, you can choose from…

view full answer...

Answer 7

In order to remove the hub/drum on your trailer you will want to first remove the spindle nut. Once the spindle nut is removed you are going to want to take a hammer and tap the outer portion of the drum as well as the hub face a few times to break…

view full answer...

Answer 8

You are correct, at this time the only option for an 8k hub drum with 5/8 inch diameter wheel studs would be a Dexter with the part #DX46XR which comes with new bearings, races, and seal.

view full answer...

Answer 9

You'll need either of the 8K hub and drum assemblies below: - 9/16" Wheel Studs #8-285-11UC3 - 5/8" Wheel Studs #DX46XR Just choose the correct matching wheel stud size and you'll be good to go! Current pricing can be found directly…

view full answer...

Answer 10

The correct grease cap for the Dexter Trailer Hub and Drum Assembly for 8,000-lb E-Z Lube Axles #DX46XR is the #TRU66FR.

view full answer...

Answer 11

The only difference between the Dexter Trailer Hub and Drum Assembly #42866UC3-EZ and the Dexter Trailer Hub and Drum Assembly #42866UC3 is that #42866UC3-EZ is designed to be used with #42 E-Z lube spindles and #42866UC3 is meant for regular #42…

view full answer...

Answer 12

The hub and drums we offer for a 7,000 lb axle we offer all use 12 x 2 inch brakes. They also have an 8 on 6-1/2 inch wheel bolt pattern. I have attached a link to the hub and drums we have that are designed for a 7,000 lb axle you can check out. If…

view full answer...

Common Torque Specifications for Lug Nut Size

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching