Recommended Winch Post/Stand For Boat Trailer With Roller Stop

Question

Question:

I need a winch post complete kit, except for the winch, ready to assemble and mount on my 3X 3inch tongue. I have the winch. The winch needs to be mounted 25inch above the tongue, the roller stop could be above or below the winch.

asked by: Fred K

0

Expert Reply:

It sounds like you are looking for the CE Smith Winch Stand - Galvanized Steel - 30" Tall x 2" Wide # CE31013G. This is designed for a 2 inch by 3 inch frame, so you will need to make some modifications. This is the only winch stand we currently carry.

You may also be interested in the Dutton-Lainson Angle Mounting Plate for StrongArm Electric Winches # DL24059 and the CE Smith Keel Roller Assembly for 2" Wide Trailer Tongues - Galvanized Steel and Yellow TPR # CE32015G.

expert reply by: Jason S

0

Answer 1

To mount the CE Smith Winch Stand #CE31013G on a trailer requires you to slip the lower portion with the holes drilled through it over the pole tongue of your trailer. The various holes are there to allow you to match the correct height and angle…

view full answer...

Answer 2

The CE Smith Winch Stand #CE31013G is basically the complete thing in and of itself. You just need to pick up appropriate hardware to install it to your trailer tongue and then install the actual winch on it and you'll be good to go. The mounting…

view full answer...

Answer 3

The Dutton-Lainson StrongArm Electric Winch, #DL25200, itself is not trailer-specific, so you could use it with any trailer provided that it is mounted properly. We have several mounting kits available depending on where you would need to mount the…

view full answer...

Answer 4

I went out to the warehouse to measure the Dutton-Lainson Angle Mounting Plate, #DL24059. The internal width of the U-bolt is 3-1/6 inches. The length is 5 inches. As long as the post is 3 inches wide by 4 inches deep, it will fit. I also spoke with…

view full answer...

Answer 5

The winch post we offer is part #CE31013G, and the typical installation for this is on a boat trailer. This post measures 30-inches tall and is designed for 2-inch wide trailer frames. It is made of 12-gauge steel and it has 14 mounting holes. I have…

view full answer...

Answer 6

It sounds like you are needing a new winch stand that will support the winch on your boat trailer. I recommend looking at the CE Smith Winch Stand #CE31013G. This is a heavy-duty stand constructed of hot-dipped galvanized, 12-gauge steel that will do…

view full answer...

Answer 7

The mounting holes on the bottom of the CE Smith Galvanized Winch Stand #CE31013G measure 7/16-inch. Please refer to the linked photo. This 30-inch tall winch stand is made of 12-gauge steel and is intended for 2-inch trailer tongues. It is…

view full answer...

Answer 8

I attached a picture that we recieved from a customer that shows the CE Smith winch mount #CE31013G installed and in use on a trailer for you to check out.

view full answer...

Answer 9

The diameter of the mounting bolt hole on the CE Smith Bow Roller Bracket for Winch Stands, #CE31005PG, is .45 inch. The bracket uses a 5-1/4 inches long x 1/2 inch diameter steel shaft for attaching the roller/Y-stop, which is part #CE10700A. The…

view full answer...

Answer 10

In order to attach the CE Smith Winch Stand part #CE31013G to your boat trailer you would need to cut off the bottom portion of the stand and weld that directly to your trailer's tongue as it is only designed to bolt onto a 2" wide trailer…

view full answer...

Answer 11

There could be two possible reasons as to why the clutch is not engaging when you are pulling in your boat with the Dutton-Lainson TW4000 StrongArm Electric Winch part #DL25200. The first reason is the simplest to fix and it entails tightening the…

view full answer...

Answer 12

Since your boat trailer has rollers on it you can use the Dutton-Lainson TW4000 StrongArm Electric Winch #DL25200 which is rated for a 4,000-lb boat when no rollers are present. This boat winch has a high-impact weather-resistant case which makes it…

view full answer...

Recommended Winch Post/Stand For Boat Trailer With Roller Stop

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching