Determining Correct Replacement Bearings for 2008 Continental Cargo Trailer

Question

Question:

I need bearings for my 2008 Continental Cargo Trailer by Forest River. Gvw 2990. I dont know which kit will work. Can you help me figure out which ones I need? Model #TW612SA.

asked by: Lauren D

0

Expert Reply:

The easiest way to determine which bearings are used on your trailer is to simply remove the hub and check for the numbers that should be stamped into the bearings themselves. If you cannot locate these numbers, another option is to take a few measurements on the trailer spindle at the bearing seat locations. I have attached an image that shows where these measurements are taken. I recommend using a digital caliper like # PTW80157 as the measurements will need to be as accurate as possible.

If you are able to locate the bearing numbers or spindle dimensions, I will be happy to recommend the correct replacement kit.

I have also attached a couple of articles on trailer hubs and bearings that you may find very helpful.

expert reply by: Chris R

0

click to enlarge

Answer 1

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 2

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

You are going to want either our Bearing Kit #BK2-100 or the Timken Kit #TMK52VR. Both of these kits will give you the inner/outer bearings and races along with a grease seal and cotter pin/D-washer for one hub. You always want to replace the race…

view full answer...

Answer 5

We recommended to repack the wheel bearings on your trailer every 12 months or 12,000 miles. There is not a specific guideline as far as actually replacing the bearings. When repacking them with grease, you will also just want to check for any damage…

view full answer...

Answer 6

Hey Barry, sure do! The seal that comes with the #DX87UR bearing kit is a 1.719" ID and 2.565" OD. We offer this seal individually as part #58846.

view full answer...

Answer 7

In order to verify the spindle dimensions so that you can pick out the correct hub/drum you have to get exact dimensions. For that you need to use a digital caliper like part #PTW80157. For how old your trailer is this is especially important as the…

view full answer...

Answer 8

Hi Tony; the #BK2-100 and #TMK52VR come with the same size bearings and grease seal. The main difference is the Timken name. This is usually associated with a higher quality bearings that are made in the USA which also accounts for the higher cost.

view full answer...

Answer 9

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 10

Hey Eric, so we do have what you need with the replacement cap part #VA55JR but the one you mentioned is smaller so it would not work for you. The cap you need is 4 inch diameter and the one you referenced is 3.75 inch.

view full answer...

Answer 11

After you've packed the bearings and assembled everything, carefully slide the hub assembly onto the spindle and install the outer bearing. Install the spindle and tang washer and run the spindle nut down finger tight, then rotate the hub back…

view full answer...

Answer 12

You can verify that the 10-19 grease seal included in Bearing Kit #BK2-100 is the correct one for your spindles by taking two measurements. First you want to measure the rear hub bore where the seal is inserted. The seal's outer diameter needs to…

view full answer...

Determining Correct Replacement Bearings for 2008 Continental Cargo Trailer

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching