Comparing Pop & Lock Manual Tailgate Locks PAL5500 and PAL5400

Question

Question:

Does the PAL5500 fit on a 2014 Tacoma the same way that PAL5400 does? Why is the 5400 more expensive that the 5500? Thanks for your help guys.

asked by: Mark M

0

Expert Reply:

Both of the Pop & Lock manual tailgate locks that you referenced, # PAL5500 and # PAL5400, are confirmed to fit your 2014 Toyota Tacoma's OEM tailgate. The difference between them is that part # PAL5400 is equipped with a lock cylinder that can be coded to match your ignition key, thanks to it including the patented BOLT coding technology.

expert reply by: Adam R

0

Answer 1

The Pop & Lock Custom Tailgate Handle with Lock and Key Alike Lock Cylinder #PAL5400 is designed to work with your 2011 Toyota Tacoma regardless if it has the backup camera or not. Since yours does have a camera, you will need to pop out a…

view full answer...

Answer 2

The Pop and Lock part #PAL5400 is the lock you would want. This lock is a fit for your 2014 Toyota Tacoma with a back up camera and would work well for you. The knock-out that you see on the handle is for your back up camera.

view full answer...

Answer 3

I have the perfect option for you to obtain a locking tailgate handle with backup camera on your 2015 Toyota Tacoma. For this, you will first want to use the Pop & Lock Custom Tailgate Lock with Handle part #PAL8540 which uses the same key as…

view full answer...

Answer 4

To use the Pop & Lock Custom Tailgate Handle with Lock and Key Alike Lock Cylinder #PAL5400 on your 2012 Tacoma that has a camera you will need their Camera Mounting Clip #PL5455CAMB. When upgrading your tailgate handle to the newer #PAL5400 this…

view full answer...

Answer 5

When it comes to replacing bearings on your Dexter 2200 pound P12 SLR axle SN: D5860714 per Dexter the inner and outer bearing number is #LM67048. Then you would need The Race #LM67010, and The Grease Seal #GS-2125DL We do not sell a kit with all the…

view full answer...

Answer 6

On a 2017 Toyota Tacoma the location to install the #3031-P is behind the kick panel to the left of your left foot. I attached a picture. You'll need to pull off the kick panel.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

To get the replacement hardware for the Draw-Tite Receiver #65070 you will need to order the Replacement Hardware Kit #RHK and type the hitch item number on the line provided.

view full answer...

Answer 10

Draw-Tite front-mount hitch #65070 is a confirmed fit on your 2012 Toyota Tacoma 4WD. We have not had a chance to install this particular item nor the Curt equivalent #31313 on your same truck so for purposes of seeing the effect on your ground…

view full answer...

Answer 11

Normally the skid plate can reinstall after the front hitch part #31313 is installed but on the TRD models the skid plate is different and can't be.

view full answer...

Answer 12

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Comparing Pop & Lock Manual Tailgate Locks PAL5500 and PAL5400

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching