Adding a 7-Way Trailer Connector to a 2005 Dodge Ram 1500 with Factory 4-Way

Question

Question:

I have a 2005 dodge ram 1500 and need to tow a pop up with a 7 way plug. The dodge has a 4 flat. The trailer has a battery that needs to recieve power as i am driving. What wire would i connect where to make sure the trailer battery is charging while i drive? I dont have a brake controller. Do i really need one? The trailer only weighs about 3500lbs loaded

asked by: Chris P

0

Expert Reply:

In order to add a 7-Way to your 2005 Dodge Ram 1500 that came with a factory 4-Way you will need to use a 4- to 7-Way adapter such as # 30717. The white wire will ground to the truck frame. The black wire is the 12 volt power circuit you will need to supply power to the trailer battery.

The black wire will need to connect to the positive battery terminal on the truck. You will need some wire and a 40 amp circuit breaker. For wire you can use # 12-1-1 which is sold by the foot. I recommend getting 25 feet so you have plenty of wire to complete the installation. For a 40 amp circuit breaker use # PK54540.

The wire will go from the 7-Way to the AUX post on the breaker then another length of wire will go from the BAT post on the breaker to the positive battery terminal.

The blue wire on the adapter is for electric brakes and the last wire is for reverse lights. If you determine that you want to add a brake controller I recommend # ETBC7 instead of the adapter, wire, and breaker listed above. The ETBC7 kit comes with all the parts you will need except for a brake controller.

Whether or not brakes are needed is largely dependent on the laws where you will be towing the trailer. Each state has different trailer braking requirements. Really it is easier and safer to just have a brake controller to activate the trailer's electric brakes. So because of that I recommend going with the ETBC7 and adding a brake controller such as the P2 # 90885. I have included some links that show and explain the ETBC7 installation for you.

expert reply by: Michael H

0

Answer 1

I recommend tracing the wiring from the 4-pole connector back to see if it plugs into a connector or if it's hardwired to your tail lights before purchasing anything. The wire harness would get all the signals right at the tail lights if it was…

view full answer...

Answer 2

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 3

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 4

Yes, there is another option to add a brake controller to your 2023 Ram 3500 and still use an app to control your settings. Since you have the factory tow package, I recommend the Curt Echo In-Line Wireless Brake Controller item #C79DR. The Echo…

view full answer...

Answer 5

If you have a vehicle specific wiring harness for a brake controller then that would indicate that you have a factory tow package and subsequently would already have a 7-way at the back of your vehicle. The universal 7-way connector #ETBC7 is meant…

view full answer...

Answer 6

The in-bed trailer wiring connector your 2008 Dodge Ram 2500 would have would be a 7-way like the part #PK11893 that you referenced. I attached a picture that has a standard 7-way wiring diagram for you to check out.

view full answer...

Answer 7

The sway control tab #RP26003 is 3/8 inch thick. The hitch balls recommended for the Ball Mount #C45270 are 2-1/8 inches long and 1 inch in diameter. So for a ball with a long enough shank you would want the part #C40020 for a 2 inch ball or part…

view full answer...

Answer 8

The remaining wires from the 4- to 7-Way adapter #37185 will need to be hardwired in to your 2003 Dodge Ram 1500 to make the 7-Way fully functional. The blue wire is for electric brakes, black is for 12 volt power, and purple is for reverse lights.…

view full answer...

Answer 9

You can use a 4-way to 7-way adapter like the part #37185 to install a Prodigy RF part #TK94FR but you have to connect the black wire of the #37185 up to the positive post of the vehicle battery through a circuit breaker like part #9510. Once you do…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Adding a 7-Way Trailer Connector to a 2005 Dodge Ram 1500 with Factory 4-Way

Products Referenced in This Question

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching