Replacing Damaged Axles and Spindles on a Yacht Club Trailer
Question:
Hi, I have a Yacht Club trailer for dual PWCs with a damaged spindle. They are welded to the axle so the axle must be replaced...do you carry any that are standard yacht club replacements or do you need all the measurements and try to match it? Thanks
asked by: Mark
Expert Reply:
In order to determine which replacement axles you need, I will need a few measurements. I will need hub face to hub face measurement, spring center to center dimension, inner and outer wheel bearing reference number, and the axle capacity. Take a look at the diagram I included.
Regarding replacement spindles, you will want to use a dial caliper to measure the dimensions of your spindle for me to recommend a new one.
The spindle measurements are labeled A through F, please view the diagram as a guide.
A is the spindle shaft diameter
B is where the grease seal sits
C is where the inner bearing sits
D is where the outer bearing sits
E is the thread diameter at the end of the spindle for the nut
F is the spindle shaft length
If you could let me know the year, model number and VIN of the trailer, we may be able to provide you with the correct information without needing the measurements.
Product Page this Question was Asked From
#84 E-Z Lube Spindle w/ Brake Flange for 3,500-lb Trailer Axle - 1-3/4" Diameter
- Trailer Spindles
- EZ Lube Spindle
- 1-3/4 Inch Diameter
- Round
- For 3500 lb Axle
- TruRyde
more information >
Continue Researching
- Shop: Trailer Wiring
- Shop: Trailer Hitch
- Video: Feature Breakdown: #84 E-Z Lube Spindle w/ Brake Flange for 3,500-lb Trailer Axle
- Q&A: What Is The Length Of The Threaded Pipes On The RV Shower Faucet # EM84FR
- Video: Phoenix Faucets RV Shower Valve w/ Vacuum Breaker Feature Review
- Video: Review of Empire Faucets Replacement Outdoor Faucet - EM84FR
- Shop: Reese Ball Mount w/ Pre-Torqued 2" Ball - 2" Hitch - 2" Drop - 7,500 lbs
- Shop: #84 E-Z Lube Spindle w/ Brake Flange for 3,500-lb Trailer Axle - 1-3/4" Diameter
- Video: What to Know About the Kenda 165/65-8 Bias Trailer Tire with 8" Galvanized Wheel w/ Offset
- Shop: Performance Chip Tuners
- Search Results: phoenix faucets rv faucets
- Search Results: 23~469
- Search Results: rv outdoor faucet
- Search Results: dura faucet
- Search Results: tru74fr
- Search Results: tru64fr
- Shop: Phoenix Faucets RV Shower Valve w/ Vacuum Breaker - Dual Knob Handle - White
- Shop: Replacement Shower Valve for D&W Inc. Spray-Away RV and Marine Unit - 4" - Black
- Shop: Easy Grease Trailer Hub and Drum Assembly for 3.5K Axles - 10" - 5 on 4-1/2 - Pre-Greased
- Shop: Replacement Shower Valve for D&W Inc. Spray-Away RV and Marine Unit - 4" - White
- Shop: Replacement Quick Disconnect Shower Valve for Empire Faucets Exterior RV Showers - Black
- Video: Tekonsha T-One Vehicle Wiring Harness Installation - 2019 Subaru Outback Wagon
- Video: Curt T-Connector Vehicle Wiring Harness Review C56040
- Video: Curt T-Connector Vehicle Wiring Harness Installation - 2019 Subaru Outback Wagon
- Search Results: alignment and lift kits trailer suspension parts
- Q&A: Is There a Benefit to Go From 14 inch Trailer Tire to 15 inch Size
- Shop: Vehicle Lights
- Q&A: Can a 4-Way Trailer Connector be Plugged Into a 5-Way Vehicle End Trailer Connector
- Q&A: Replacement 5-Way Recommendation to Replace a 5-Way that Had 7-Wires Run to It
- Q&A: How to Tell if Trailer has a BT8 or BTR Spindle Installed
Jason T.
6/25/2024
Hi I have a double axel boat trailer hatch club brand , not sure the year but I am trying to find 4 hubs that will fit. Here is the info of the label MFD. GVWR JANUARY 5800 HUM ERS 9548 MAX. LOAD CARRYING CAP. 5000 GAWR EA. AXLE 2800/G78-14B TIRES 14 X 6 OR 14 X 3 1/2 RINS € 32 PSI COLD THIS VEHICLE CONFORMS TO ALL APPLICABLE MOTOR VEHICLE SAFETY STANDARDS IN EFFECT ON THE DATE OF MANUFACTURE SHOWN ABOVE. VEHICLE I.D. NO. MODEL 4H1002322P0124428 VEHICLE CLASS: R22487- BOAT TRAILER